764024
6
Zoom out
Zoom in
Previous page
1/144
Next page
6
EN
may significantly increase the exposure level
- thetimeswhenthetoolisswitchedofforwhen
it is running but not actually doing the job, may
significantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
DESCRIPTION (FIG. A)
Your multitool has been designed for light
sanding, sawing and scraping applications.
1. On/offswitch
2. Speed adjustment wheel
3. Mountingpointforaccessories
4. Grip
5. Allen key
6. Allenkeyholder
13.Carbonbrushcover
ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the sanding pad and
the sanding paper (fig. B)
The sanding pad and the sanding paper must be
used for sanding applications.
Mounting
• Placethemachineonatablewiththemounting
point(3)facingupwards.
• LoosentheAllenscrew(7)usingtheAllenkey(5).
• Mountthesandingpad(9)tothemountingpoint
(3).
• TightentheAllenscrew(7)usingtheAllenkey(5).
• Mountsandingpaper(10)withtherequired
grainsizeontothesandingpad(9).Makesure
thattheperforationinthesandingpaper(10)
corresponds with the perforation on the sanding
pad(9).
- Usecoarsesandingpaper(grain50)for
sanding rough, uneven surfaces.
- Usemediumsandingpaper(grain80)for
removing the remaining scratches from the
coarse sanding paper.
- Usefinesandingpaper(grain120)for
finishing surfaces.
Removing
• Placethemachineonatablewiththemounting
point(3)facingupwards.
• Removethesandingpaper(10)fromthesanding
pad(9).
• LoosentheAllenscrew(7)usingtheAllenkey(5).
• Removethesandingpad(9)fromthemounting
point(3).
• TightentheAllenscrew(7)usingtheAllenkey(5).
Mounting the dust extraction (fig C1 + C2)
The dust extraction piece can be used to connect
the machine to a vacuum cleaner when sanding.
Dustwillbeextractedandyourworkareastays
cleaner.
the dust extraction adapter can only be
used in combination with the sanding
pad (9).
To install the dust extraction adapter:
• Ifnotdoneyet,removetheaccessoriesfrom
themachinespindle(3).
• Assemblethedustextractionparts(15Ato
15D)togetherlikeshownin(Fig.C1andC2)
• Clicktheadaptertothemachinespindleuntil
itfixeswell,makesuretherearfingers(15C)
click into the gaps on the machine housing.
• Addthefeltring(15E)betweenthepadandthe
adapter for a tight sealing and assemble the
sanding pad like instructed in previous chapter.
• Connectavacuumcleanertotheadapterend
(15D).
Mounting and removing the saw blade (fig. B)
The saw blade must be used for sawing applications.
Mounting
• Placethemachineonatablewiththemounting
point(3)facingupwards.
• LoosentheAllenscrew(7)usingtheAllenkey(5).
• Removethespacer(8).
• Mountthesawblade(11)tothemountingpoint
(3).
• Mountthespacer(8).
• TightentheAllenscrew(7)usingtheAllenkey(5).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm OTM1005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm OTM1005 in the language / languages: All languages as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info