510120

Ferm MSM1034 Manual

10
Zoom out
Zoom in
Previous page
1/72
Next page
EN
10 Ferm
b. As a stationary machine on the subframe. In
this case the machine must be secured to the
subframe with 4 bolts and the subframe
anchored to the floor or to a floor plate with
dimensions of at least 1 square meter.
Guide fence insert
Fig. H, I, J
For safety reasons, this machine is equipped with
a guide fence insert
to be used when using the machine for sawing
straight cross-cuts.
• For sawing straight cross-cuts, the guide
fence insert must remain mounted on the
machine (fig. H).
• For sawing mitre cuts, the guide fence insert
must be removed from the machine as shown
(fig. H).
• For sawing bevel cuts, the guide fence insert
must be removed from the machine as shown
(fig. I+J).
Mounting and removing the saw blade
Fig. A+B
Do not use the machine without the
guard.
Mounting
• Pull out the locking knob (3) and raise the saw
head (12).
• Loosen the bracket (29) by removing the
screw (30).
• Raise the guard (6).
• Keep the spindle lock button (7) pressed and
loosen the bolt (19) using the spanner (20).
• Remove the flanges (21 & 22).
• If necessary, clean the flanges (21 & 22).
• Mount the flange (22).
• Mount the saw blade (5). Make sure that the
arrow on the saw blade points in the same
direction as the arrow on the saw head.
• Mount the flange (21).
• Keep the spindle lock button (7) pressed and
tighten the bolt (19) using the spanner (20).
• Lower the guard (6).
• Mount the bracket (29) by tightening the screw
(30).
Removing
• Pull out the locking knob (3) and raise the saw
head (12).
• Loosen the bracket (29) by removing the
screw (30).
• Raise the guard (6).
• Keep the spindle lock button (7) pressed and
loosen the bolt (19) using the spanner (20).
• Remove the flange (21).
• Remove the saw blade (5).
• Mount the flange (21).
• Keep the spindle lock button (7) pressed and
tighten the bolt (19) using the spanner (20).
• Lower the guard (6).
• Mount the bracket (29) by tightening the screw
(30).
Setting the mitre angle
Fig. C
• The mitre angle is left/right variable between
0° and 45°. The mitre angle can be read from
the scale (9).
Do not set the mitre angle during use.
• Slacken the locking knob (8).
• Turn the saw table (13) to the required
position.
• Tighten the locking knob (8).
Setting up the double sawing angle / mitring
Fig. D
• Adjust the first angle as described for
adjusting the saw angle (above).
• Turn the knob (10) anticlockwise and then set
the angle desired (you can read this off on the
back of the machine. Then tighten the knob
(10) again by turning it clockwise.
Changing the carbon brushes
Fig. A
• Make sure that the plug is not in the socket!
• Unscrew the covers (16) with a flat bladed
screwdriver. Remove the carbon brushes with
the same type of brushes. Screw the covers
(16) tight again.
Note: Always replace both carbon brushes at the
same time. Never use a mixture of old and new
brushes.
Mounting the dust bag
Fig. F
Press in the clamp of the dust bag (27) and slide it
onto the opening on the back of the machine. The
dust bag stays in place when you release the clamp.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1034 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1034 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info