510120

Ferm MSM1034 Manual

11
Zoom out
Zoom in
Previous page
1/72
Next page
EN
11
Ferm
4. Operation
Using the mitre saw
Fig. 1
Before use, always check for faults or
defects!
• Set the desired sawing angle of the machine.
• Put the plug into the socket.
• Fix the piece of work in place using the clamps
(24): make sure that the material is well
clamped in place!
• Hold the material tightly on the left side while
making sure that you keep a safe distance
from the blade of the saw.
• Turn on the machine using the switch (1).
• Make sure that the saw blade has reached full
speed before allowing it to touch the piece of
work to be sawn.
• Use knob (2) to raise the protective cover lock.
• Now bring the saw slowly downwards so that
the saw blade saws through the piece of work
and passes through the slot in the table. Do
not put any pressure on the saw. Give the
machine time to saw through the piece of
work.
• Bring the machine gently up again and switch
it off by letting go of the switch (1).
5. Service & maintenance
Always make sure that the machine is not
connected to the mains electricity when
you carry out any maintenance of the
mechanism.
This machine has been designed to operate over
a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
Repairs and servicing should only be
carried out by a qualified technician or
service firm.
Problem solving
1. The motor does not start
• The plug is not in the socket
• The power cord is broken
• The switch is defective. Take the machine to
your Ferm dealer for repair.
2. The saw cut is not even (jagged)
• The saw blade must be sharpened
• The saw blade is mounted back to front
• The saw blade is clogged with resin or
sawdust
• The saw blade is not suitable for the piece of
work being used
3. The height and/or mitre lever is obstructed
• Chips and/or dust must be removed
4. The motor has difficulty in reaching full
speed
• The extension cord is too thin and/or too long
• The mains voltage is less than 230 V
5. The machine vibrates excessively
• The saw blade is damaged
6. The machine becomes excessively hot
• The ventilation slots are blocked. Clean them
out with a dry cloth.
7. The electromotor runs unevenly
• The carbon brushes are worn out. Replace the
carbon brushes or consult your Ferm dealer.
Cleaning
Regularly clean the device’s casing with a soft
cloth, preferably after each use. Keep the fan slits
free of dust and dirt. Remove stubborn dirt using a
soft cloth, dampened with soapy water. Do not use
solvents such as benzene, alcohol, ammonia, etc,
which might damage the plastic parts.
Lubrication
The device does not need any additional
lubrication.
Defects
If a defect appears due to a part wearing out,
please contact the service center on the warranty
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1034 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1034 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info