Manual Ferm MSM1031 (page 8 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

493544

Zoom out

Zoom in

1/120

(fig. 7).

• For sawing bevel cuts, the guide fence insert

must be removed from the machine as shown

(fig. 7)



• Mount the support bracket into the slot in the

rear of the base.

• Tighten the screw to secure the support

bracket.

Changing the saw blades

Fig. 4

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

• Make sure that the plug is not in the socket!

• Lock the head of the machine in its highest

position.

• Move the hood (6) forwards. Push the saw

blade interlock (22) in and unscrew the bolt

(18) with the key supplied (clockwise).

• Remove the saw blade flange (19) and

change the blade. Make sure that the blade is

mounted in the machine correctly: with the

arrow on the blade pointing clockwise.

• Replace the flange (19) and push the interlock

(22) in and screw the bolt (18) tight again.

Adjusting the saw angle

• Unscrew the knob (9) a half turn clockwise.

• Turn the machine to the desired angle (the

angle can be read off on the front of the

machine).

• Screw up the knob (9) a half turn

anticlockwise.

Setting up the double sawing angle / mitring

Fig. 2 + 3

• Adjust the first angle as described for

adjusting the saw angle (above).

• Turn the knob (12) anticlockwise and then set

the angle desired (you can read this off on the

back of the machine. Then tighten the knob

(12) again by turning it clockwise.

Changing the carbon brushes

Fig. 1

• Make sure that the plug is not in the socket!

• Unscrew the covers (4) with a flat bladed

screwdriver. Remove the carbon brushes with

the same type of brushes. Screw the covers

(4) tight again.

Note: Always replace both carbon brushes at the

same time. Never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. 3

Press in the clamp of the dust bag and slide it

onto the opening (13) on the back of the machine.

The dust bag stays in place when you release the

clamp.



Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

• Set the desired sawing angle of the machine.

• Put the plug into the socket.

• Fix the piece of work in place using the

clamps (7): make sure that the material is well

clamped in place!

• Hold the material tightly on the left side while

making sure that you keep a safe distance

from the blade of the saw.

• Turn on the machine using the switch (1).

• Make sure that the saw blade has reached full

speed before allowing it to touch the piece of

work to be sawn.

• Use knob (3) to raise the protective cover

lock.

• Now bring the saw slowly downwards so that

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

• Bring the machine gently up again and switch

it off by letting go of the switch (1).

Using the slide-function

Fig. 2

The machine must be firmly bolted to a

workbench.

Use the slide-function for sawing wide

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1031 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1031 Manual

Product: