Manual Ferm MSM1031 (page 7 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

493544

Zoom out

Zoom in

1/120

machine

• Push the button in the handgrip to unlock the

saw blade protection

• Push the machine completely downwards

• Lock the pin on the right hand side again

Only lift the machine by the solid underside of the

machine.

While the machine is in use

With frequent use of the machine, do not let

routine lead to mistakes. Remember that a slight

lack of concentration can lead to serious injuries

in a fraction of a second.

• Before beginning to saw, make sure that the

protective hood is in the right position.

• Before cutting the first cut, let the machine run

for a short while. If you hear any unusual

sounds or observe any strong vibration, turn

the machine off and take the plug out of the

socket, and then find the cause of the

problem. Do not switch the machine on again

until the cause has been found and the fault

repaired.

• Make sure that the piece of work being sawn

off does not get stuck in place, do not hold it or

clamp it and no not secure it against the stop.

It must be able to move freely along the side

of the saw blade. When this is not possible the

piece of work being sawn can be trapped by

the saw blade and be flung about.

• Avoid placing your hands anywhere where in

the case of a sudden movement one or both

hands can come into contact with the saw

blade.

• Let the saw get up to full revolutions before

you start sawing.

• Press the saw head downwards so that the

motor is not overloaded and the saw blade

does not get jammed.

• If you need to remove jammed material, first

let the saw blade stop turning completely,

switch the motor off and take the plug out of

the socket.

• At the end of the sawing process, keep the

saw head downwards, switch off the machine

and wait until all moving parts has come to a

stop before you take your hands off the

machine.

Motor

• Connect the machine to a 220/230 Volt

socket.

• If the motor does not start, immediately

release the switch. Take the plug out of the

socket. Check that the saw blade can turn

freely. If so, try starting the machine again.

To prevent damaging the motor must be

regularly freed of chips and dust to

ensure correct cooling.

• If the motor suddenly stops while sawing, let

go of the switch immediately. Loosen the saw

blade from the piece of work, after which

sawing can continue.

• Using long cables of too small a diameter can

result in loss of voltage, which can lead to

problems with the motor.

• For a length up to 15 metres a cable must be

used with a diameter of 1.5 mm

• For a length of between 15 and 40 metres a

cable must be used with a diameter of 2.5



Installation of the mitre saw

Figs. 1 and 2

• Place one extension piece (21) on the right-

hand side of the machine and the other

extension piece (21) on the left-hand side of

the machine.

• Loosen the locking bolts (23) and slide the

guide rods in the openings.

• Tighten the locking bolts again (23).

• Place the work piece clamp (7) on the left or

right side of the machine.

• Hold the handgrip and move the saw slightly

downwards and then pull the pin (5) out

slightly so that the machine comes free.

Note: Never use the mitre saw without the

extension pieces supplied. Make sure that they

are correctly mounted.

Guide fence insert

For safety reasons, this machine is equipped with

a guide fence insert to be used when using the

machine for sawing straight cross-cuts.

• For sawing straight cross-cuts, the guide

fence insert must remain mounted on the

machine (fig. 6).

• For sawing mitre cuts, the guide fence insert

must be removed from the machine as shown

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1031 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1031 Manual

Product: