Manual Ferm hdm 1017 (page 7 of 124) (English, German, Dutch, French, Italian)

388771

Zoom out

Zoom in

1/124

Hammer drilling in concrete or brick

Caution: Stone drills can get very hot.

It may be necessary to drill with smaller bits and

re-drill to nominal size so that later the plug is

rmly seated.

For large bores, for instance in very hard

concrete, use a smaller bit for pilot drilling and

re-drill to nominal size.

Do not apply a lot of pressure on the machine, let

the machine do the work, guiding the machine

with light pressure is sufcient.

Hold the machine with the auxiliary handle, the bit

can jam, particularly with deep bores, and the

machine will turn.

Chipping in concrete and brick

You can also use the machine for chipping.

Prior to starting work ensure that the front selec-

tion switch and handle selection switch are fully

engaged. Do not operate the hammer drill with

selection switches in mid position. Only change

the function when the motor has come to a

standstill.

Here as well: Do not apply a lot of pressure on

the machine, let the machine do the work, guiding

the machine with light pressure is sufcient.

4. MAINTENANCE

Take care that the machine is not

connected to power whenever

maintenance work on the mechanical

parts is taking place.

These machines are designed to function

problem-free for a long period with a minimum of

maintenance. Through regular cleaning and

correct treatment, you help assure a long working

life for your machine.

Defects

The machine should be regularly inspected for

the following possible defects, and repaired if

necessary.

• Damage to power cord

• Broken on/off trigger assembly.

• Short circuiting.

• Damaged moving parts.

Trouble shooting

1. When switched on, the motor does not turn

• Failure in power supply.

• Check the power supply.

• Poor contact in the on/off trigger.

• Repair or replace the trigger assembly.

• Mains voltage too low.

• Extension lead too long, or too light.

• Damaged motor.

• Have your machine repaired by an expert.

• Carbon brushes worn.

• Replace the carbon brushes.

2. Motor generates excessive noise, and runs

too slowly or not at all

• Motor is overloaded due to excessive pressure

or drilling depth.

• Reduce the pressure or drilling depth,

reduce power.

• Damaged motor.

• Have your machine repaired by an expert.

• Supply voltage too low.

• Adjust the supply voltage.

• Carbon brushes worn.

• Replace the carbon brushes.

3. Overheating in the transmission case

• Overloading of machine, or blunt drill bit

• Reduce the loading, or hone the drill bit.

• Reduced voltage.

• Adjust the supply voltage.

4. Heavy sparking from the motor

• Inspect the carbon brushes for wear.

Cleaning

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and dirt.

Remove very persistent dirt using a soft cloth

moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia, etc.

Chemicals such as these will damage the

synthetic components.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. Separate you nd an exploded

view showing the parts that can be ordered.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm hdm 1017 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm hdm 1017 Manual

Product: