Manual Ferm hdm 1017 (page 6 of 124) (English, German, Dutch, French, Italian)

388771

Zoom out

Zoom in

1/124

Exchanging and removing drill bits

Fig. A + B

Before exchanging bits, rst remove the

power plug from the wall socket.

Inspect bits regularly during use. Blunt

bits should be re-sharpened or replaced.

• Lightly oil the bit shaft before inserting it into

the chuck.

• Slide the locking sleeve (7) to the rear, and

insert the bit into the chuck opening. Ensure

that the keyway in the bit is seated properly in

the chuck, by carefully turning the bit until it

clicks into place. Release the locking sleeve.

• To remove the bit, slide and hold the locking

sleeve to the rear.

Setting depth gauge

Fig. A

• Loosen the handgrip by turning it

anticlockwise.

• Insert the depth gauge ruler through the hole

in the auxiliary handgrip.

• Slide the ruler to the desired depth.

Retighten the screw rmly.

Function selection switch

Fig. C

The correct position of the selection switch for

each machine function is given in the diagram

(Fig.C) on page 3.

A: Drilling

B: Hammer Drilling

C: Chisel angle adjustment

D: Demolition hammer/chisel

The On/Off switch

Fig. A

• Switch the machine on by pressing the

triggerswitch (2). When you release the

triggerswitch (2) the machine will turn off.

Switch-lock

• You can lock the On/Off switch by pressing the

triggerswitch (2) and then pressing knob (4).

Release the switch-lock by pressing the

triggerswitch (2) shortly.

Speed-control

• The rotation-speed can be continuously

adjusted from 0 to 950 and 0 to 4500 rotations

per minute by pressing the switch (2) deeper

or less deep.

Adjusting of the maximum rotation speed

• Switch the machine on by pressing

triggerswitch (2).

• Lock the triggerswitch (2) by pressing knob

(4).

• Adjust the speed by turning the small wheel

(3) to the desired maximum rotation speed.

Switching the direction of rotation

• Direction of rotation counter-clockwise: shift

switch to “►”.

• Direction of rotation clockwise: shift switch to

“◄”.

This function is only available when the machine

is set to “drill mode”.

Chuck

A chuck with SDS-10 shaft is shipped with the

product. Please note that the machine is

particularly suited for hammer drilling, the chuck

should only be used for occasional simple drill

work.

• Use the chuck key to open and close the

chuck.

• Introduce the chuck key into one of the three

holes in the chuck and open the chuck by

turning anticlockwise, close the chuck by

turning clockwise.

• Always remove the chuck key from the chuck.

Never run the machine with the chuck key

inserted.

• Ensure that the switch (2) is in the OFF

position.

• Only connect the device to the mains power if

this is the case.

User tips

Always use the machine with the auxiliary

handgrip rmly anchored in place – you will not

only work with more comfort, you will also work

with more precision.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm hdm 1017 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm hdm 1017 Manual

Product: