427174

Ferm fws 125 4k wall slotter Manual

9
Zoom out
Zoom in
Previous page
1/120
Next page
9
EN

● To switch on the machine, keep the lock-off
button (2) pressed and simultaneously press
the on/off switch (1).
● To switch off the machine, release the on/off
switch (1).
Overload protection
The machine is equipped with an overload
protection device which automatically switches off
the machine if the machine is overloaded.
● Switch off the machine.
● Remove the machine from the workpiece.
● Switch on the machine.
● Run the machine at no-load for approximately
1 minute to allow the machine to cool down.

The laser is used for projection of the cut on the
wall.
● To switch on the laser (8), press the on/off
switch (7).
● To switch off the laser (8), release the on/off
switch (7).

Only use the machine when it is connected to a
vacuum device which is approved for stone dust.
The vacuum device must be suitable for the
material to be worked. Use a special vacuum
device when working with toxic materials or
where toxic dust is produced.
2
- Never use a household vacuum cleaner.
The use of a household vacuum cleaner can
easily damage both your health and the
vacuum cleaner.
- Always use the dust extraction adapter.
- Make sure that the hose of the vacuum device
is securely connected to the dust extraction
adapter.
- If the vacuum device breaks down, stop work
immediately, switch off the machine, remove
the mains plug from the mains, and try to solve
the problem.
● Insert the dust extraction adapter (26) into the
dust extraction connection (12).
● Connect the hose of a vacuum device to the
dust extraction adapter (26).
Hints for optimum use
● Draw lines to dene the direction in which to
guide the cutting discs.
● Hold the machine with both hands.
● Set the slot width.
● Take one of the following steps:
- Lower the machine into the wall and set the
slot depth (recommended). The machine is
placed against the wall and the cutting discs
lower into the wall in order to set the slot
depth more accurately.
- Set the slot depth and lower the machine
into the wall.
● Place the machine with the guide roller on the
wall. Make sure that the cutting discs align
with the drawn lines on the wall.
● Set the slot depth.
● Switch on the machine.
● Wait until the machine has reached full speed.
● Slowly move the machine along the pre-drawn
lines, rmly pressing the guide roller against
the wall.
● Do not apply too much pressure on the
machine. Let the machine do the work.
● Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
CLEANING AND MAINTENANCE
4
Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
● Regularly clean the housing with a soft cloth.
● Keep the ventilation slots free from dust and
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
● Regularly clean the cutting discs to avoid
inaccuracies during use.

The laser uses 2 AAA batteries. If the laser stops
working, the batteries must be replaced.
● Remove the cover (27) from the battery
compartment (9).
● Remove the old batteries (28).
● Place the new batteries (28).
● Mount the cover (27) to the battery
compartment (9).
WARRANTY
Consult the enclosed warranty terms.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fws 125 4k wall slotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fws 125 4k wall slotter in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info