427174
8
Zoom out
Zoom in
Previous page
1/120
Next page
8
EN
- the times when the tool is switched off or when
it is running but not actually doing the job, may
signicantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
DESCRIPTION (FIG. A)
Your wall slotter has been designed for making
slots in masonry. The machine is only suitable for
right-hand use.
1. On/off switch
2. Lock-off button
3. Locking knob for slot depth
4. Scale for slot depth
5. Spindle lock button
6. Guard
7. On/off switch for laser
8. Laser
9. Battery compartment
10. Base
11. Guide roller
12. Dust extraction connection
13. Main grip
14. Auxiliary grip
ASSEMBLY
4
Before assembly, always switch off the
machine and remove the mains plug
from the mains.

Worn or damaged cutting discs must be replaced
immediately.
2
- Only use sharp and undamaged cutting discs.
- Only use cutting discs that are suitable for the
material to be worked.
- Only use cutting discs with a maximum
permitted speed that is equal to or exceeds
the maximum no-load speed of the machine.
- Only use diamond cutting discs that are
suitable for dry cutting.
- Always replace both cutting discs at the same
time.
- Never attempt to remove the guard.
Place the machine on a stable surface.
Loosen the Allen screws (15) using the Allen
key (16).
Loosen the locking knob (3) and lower the
base (10).
Remove the guard (6).
Keep the spindle lock button (5) pressed to
lock the spindle (17).
Loosen the outer ange (18) using the ange
key (19).
Remove the old cutting disc (20), the spacers
(21), the old cutting disc (22), the spindle
sleeve (23), and the inner ange (24).
If necessary, use the splitting wedge (25) to
remove the spacers (21).
If necessary, clean the anges (18 & 24).
Mount the inner ange (24), the spindle sleeve
(23), the new cutting disc (22), the spacers
(21), and the new cutting disc (20).
Firmly tighten the outer ange (18) using the
ange key (19).
Release the spindle lock button (5).
Mount the guard (6).
Raise the base (10) and tighten the locking
knob (3).
Firmly tighten the Allen screws (15) using the
Allen key (16).
USE

The slot width can be set using the spacers
between the cutting discs. The number of spacers
between the cutting discs determine the slot width.
2
- Do not set the slot width during use.
- Always mount at least one spacer between the
cutting discs.
Determine the slot width.
Mount the spacers (21) around the cutting
discs (20 & 22) in the required order. Refer to
the chapter “Replacing the cutting discs”.

The slot depth is variable between 0 and 28 mm.
The slot depth can be read from the scale (4).
2
Do not set the slot depth during use.
Slacken the locking knob (3).
Tilt the base (10) to the required position. Set
a slot depth approximately 3 mm deeper than
the required depth to compensate for possible
unevenness of the wall surface.
Tighten the locking knob (3).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fws 125 4k wall slotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fws 125 4k wall slotter in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info