427174

Ferm fws 125 4k wall slotter Manual

7
Zoom out
Zoom in
Previous page
1/120
Next page
7
EN
● Never put the machine down on a table or a
workbench before it has been switched off.
Kickback
Kickback is the upward and backward movement
of the cutting discs when the cutting discs
unexpectedly touch an object. Securely hold the
machine with both hands during use. Keep your
attention focused on the operation.
Kickback is usually caused by:
- unintentionally touching hard objects or
materials with the rotating cutting discs;
- blunt cutting discs;
- cutting discs that are not properly mounted;
- cutting into a previous cut;
- a lack of attention to the operation;
- an instable stance.
Additional safety warnings for lasers
● Do not look directly into the laser beam.
● Do not point the laser beam humans or animals.
● Do not point the laser beam at strongly
reecting material.
● Do not insert hard objects into the laser optics.
● Clean the laser optics with a soft, dry brush.
● Only have the laser repaired by a qualied
technician.
ELECTRICAL SAFETY
3
Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate.
● Do not use the machine if the mains cable or
the mains plug is damaged.
● Only use extension cables that are suitable for
the power rating of the machine with a
minimum thickness of 1.5 mm
2
. If you use a
extension cable reel, always fully unroll the
cable.
Mains plug replacement (UK only)
If the moulded 3-pin plug attached to the unit is
damaged and needs replacing, it is important that
it is correctly destroyed and replaced by an
approved BS 1363/13A fused plug and that the
following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
blue neutral
brown live
As the colours of the wires in the mains cable of
the unit may not correspond to the coloured
markings identifying the terminals in the plug,
proceed as follows:
- The wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black.
- The wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
TECHNICAL DATA
WSM1009
Mains voltage V~ 230
Mains frequency Hz 50
Power input W 1,700
No-load speed min
-1
4,000
Slot width mm 14 / 19 / 29
Slot depth mm 0 - 28
Cutting disc
Diameter mm 125
Bore mm 22.2
Spindle thread M12
Protection class IP 20
Laser class 2
Battery type AAA
Weight kg 5.1
NOISE AND VIBRATION
WSM1009
Sound pressure (L
pa
) dB(A) 109
Acoustic power (L
wa
) dB(A) 120
Uncertainty (K) dB(A) 3
Vibration (main grip) m/s
2
1.32
Vibration (auxiliary grip) m/s
2
2.86
Uncertainty (K) m/s
2
1.5
2
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruction
manual has been measured in accordance with a
standardised test given in EN 60745; it may be used
to compare one tool with another and as a
preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories,
may signicantly increase the exposure level
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fws 125 4k wall slotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fws 125 4k wall slotter in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info