Manual Ferm FRS 600 (page 5 of 24) (English, German, Dutch, Danish, French, Italian, Norwegian)

110162

Zoom out

Zoom in

1/24

ADJUSTING THE FOOT PLATE ANGLE

Fig.D

• To allow the foot plate to follow and securely rest on

the workpiece, the angle of the footplate can be

adjusted as shown in the diagram.

• The footplate can also be extended by loosening the

two footplate length adjustment screws (Fig. A8)

using the 4 mm hexagon key and then pulling the foot-

plate out to the required length.

Ensure the footplate adjustment screws are secure

before resuming work.

SAWING TIPS

• Adjust saw blade and stroke rate to suit the material

to be processed. For right radius curves it is best to

use a narrow saw blade. Apply coolant or lubricant to

deal with the beat produced along the cut line when

sawing metal.

• Check wood, chip boards, building materials etc, for

foreign bodies (nails, screws etc.), before sawing and

remove them, if necessary.

• Clamp material well. Do not support the workpiece

with hand or foot. Do not touch objects or the floor

with the saw running (danger of backlash).

• Material containing asbestos must not be sawn!

• Put the footplate on the surface of the workpiece,

and saw through it with constant contact pressure or

feed. If the saw blade seizes switch the machine off

immediately . Spread the gap with a suitable tool and

pull out the saw blade.

• After finishing work, switch off the machine and only

put down after it has come to a complete standstill.

PLUNGE CUTTING

Fig.E

• Plunge cutting may only be used on soft materials

such as wood, aerated concrete, gypsum plaster

boards, etc.

• However, this requires a certain practise and is only

possible with short saw blades.

• Place the saw onto the workpiece and switch it on.

• Ensure that the bottom edge of the footplate rests on

the workpiece surface as shown.

• Slowly saw into the workpiece at an angle, moving the

saw to a vertical position and continue to saw along

the cutting line.

• Switch the saw off and lift off the workpiece when the

work is complete.

FLUSH SAWING

• Elastic bi-metal saw blades allow you to saw projec-

ting objects (e,g, water pipes, iron bars, etc,) flush

against the wall.

• Apply the saw blade directly to the wall and bend

slightly so that the footplate rests against the wall.

• Switch the machine on and saw off the workpiece

keeping constant lateral pressure against the wall.

There are no user servicable parts in this unit. Any

repairs or servicing should be carried out by qualified

service en-gineers.

TROUBLESHOOTING

In case the machine does not work well, we give you

some possible causes and solutions.

1. The electromotor gets hot

• The cool ventilation slots in the motor are stopped

up with dirt.

Clean the cool ventilation slots.

• The motor is defect.

Have your machine repaired or checked by your local

Ferm dealer.

2. The connected machine does not work

• Interruption in the mains connection.

Check mains connection for fracture.

Have your machine repaired/checked by your local

Ferm dealer.

Repairing of electric appliances may be carried out

only by experts.

MAINTENANCE

Make sure that the machine is not live when car-

rying out maintenance work on the motor.

The Ferm machines have been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon pro-

per machine care and regular cleaning.

Cleaning

Keep the ventilation slots of the machine clean to pre-

vent overheating of the engine.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.

If the dirt does not come off use a soft cloth moistened

with soapy water. Never use solvents such as petrol,

alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please con-

tact your local Ferm dealer.

In the back of this manual you find an exploded view

showing the parts that can be ordered.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these

materials to the appropriate recycling locations.

Take your unwanted machines to your local Ferm-

dealer. Here they will be disposed of in an environmen-

tally safe way.

Ferm 5

ìëíêÄçÖçàÖ çÖèéãÄÑéä

å‡¯ËÌ‡ ÌÂ ËÏÂÂÚ ˜‡ÒÚÂÈ, ÍÓÚÓ˚È ÏÓÊÂÚ

ÂÏÓÌÚËÓ‚‡Ú¸ ‚Î‡‰ÂÎÂˆ. êÂÏÓÌÚ Ë ÚÂıÌË˜ÂÒÍÓÂ

Ó·ÒÎÛÊË‚‡ÌËÂ ‰ÓÎÊÌ˚ ‚˚ÔÓÎÌﬂÚ¸Òﬂ

Í‚‡ÎËÙËˆËÓ‚‡ÌÌ˚Ï ÒÂ‚ËÒÌ˚Ï ÔÂÒÓÌ‡ÎÓÏ.

çËÊÂ ÔË‚Ó‰ËÚÒﬂ ﬂ‰ ÌÂÔÓÎ‡‰ÓÍ, Ëı ‚ÓÁÏÓÊÌ˚Â

ÔË˜ËÌ˚ Ë ÏÂÚÓ‰˚ ÛÒÚ‡ÌÂÌËﬂ.

1. ùÎÂÍÚÓ‰‚Ë„‡ÚÂÎ¸ ÔÂÂ„Â‚‡ÂÚÒﬂ

• ÇÂÌÚËÎﬂˆËÓÌÌ˚Â ˘ÂÎË ‰Îﬂ ÓıÎ‡Ê‰ÂÌËﬂ Á‡·ËÎËÒ¸

„ﬂÁ¸˛.

èÓ˜ËÒÚËÚ¸ ‚ÂÌÚËÎﬂˆËÓÌÌ˚Â ˘ÂÎË.

• ùÎÂÍÚÓ‰‚Ë„‡ÚÂÎ¸ ÌÂËÒÔ‡‚ÂÌ.

é·‡ÚËÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm ‰Îﬂ

ÓÒÏÓÚ‡ ËÎË ÂÏÓÌÚ‡.

2. ëÓÂ‰ËÌÂÌÌ‡ﬂ Ò ÒÂÚ¸˛ Ï‡¯ËÌ‡ ÌÂ ‡·ÓÚ‡ÂÚ

• é·˚‚ ‚ ÒÓÂ‰ËÌÂÌËË Ò ÒÂÚ¸˛.

èÓ‚ÂËÚ¸ ÒÓÂ‰ËÌÂÌËÂ Ò ÒÂÚ¸˛ Ì‡ Ó·˚‚.

é·‡ÚËÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm ‰Îﬂ

ÓÒÏÓÚ‡ ËÎË ÂÏÓÌÚ‡.

êÂÏÓÌÚ ˝ÎÂÍÚË˜ÂÒÍËı ÔË·ÓÓ‚ ‰ÓÎÊÂÌ

‚˚ÔÓÎÌﬂÚ¸Òﬂ ÚÓÎ¸ÍÓ ÒÔÂˆË‡ÎËÒÚ‡ÏË.

íÖïçàóÖëäéÖ

éÅëãìÜàÇÄçàÖ

ÇÒÂ„‰‡ ÓÚÍÎ˛˜‡ÈÚÂ Ï‡¯ËÌÛ ÓÚ ÒÂÚË ÔÂÂ‰

‚˚ÔÓÎÌÂÌËÂÏ ÚÂıÌË˜ÂÒÍÓ„Ó Ó·ÒÎÛÊË‚‡ÌËﬂ

˝ÎÂÍÚÓ‰‚Ë„‡ÚÂÎﬂ.

å‡¯ËÌ‡ ‡ÒÒ˜ËÚ‡Ì‡ Ì‡ ‰ÎËÚÂÎ¸ÌÛ˛ ‡·ÓÚÛ Ò

ÏËÌËÏ‡Î¸Ì˚Ï Ó·˙ÂÏÓÏ ÚÂıÌË˜ÂÒÍÓ„Ó Ó·ÒÎÛÊË‚‡ÌËﬂ.

êÂ„ÛÎﬂÌ‡ﬂ ˜ËÒÚÍ‡ Ë Ô‡‚ËÎ¸ÌÓÂ Ó·‡˘ÂÌËÂ

Û‚ÂÎË˜Ë‚‡˛Ú ÒÓÍ ÒÎÛÊ·˚ Ï‡¯ËÌ˚.

óËÒÚÍ‡

ëÓ‰ÂÊËÚÂ ‚ÂÌÚËÎﬂˆËÓÌÌ˚Â ˘ÂÎË ˜ËÒÚ˚ÏË ‰Îﬂ

ÔÂ‰ÓÚ‚‡˘ÂÌËﬂ ÔÂÂ„Â‚‡.

êÂ„ÛÎﬂÌÓ ÔÓÚË‡ÈÚÂ Ï‡¯ËÌÛ Ïﬂ„ÍÓÈ ÚÍ‡Ì¸˛,

ÊÂÎ‡ÚÂÎ¸ÌÓ ÔÓÒÎÂ Í‡Ê‰Ó„Ó ËÒÔÓÎ¸ÁÓ‚‡ÌËﬂ. ì‰‡ÎﬂÈÚÂ

Ô˚Î¸ Ë ‰Û„ËÂ ÓÚÎÓÊÂÌËﬂ ËÁ ‚ÂÌÚËÎﬂˆËÓÌÌ˚ı ˘ÂÎÂÈ.

ëÚÓÈÍËÂ Á‡„ﬂÁÌÂÌËﬂ Û‰‡ÎﬂÈÚÂ Ïﬂ„ÍÓÈ ÚÍ‡Ì¸,

ÒÏÓ˜ÂÌÌÓÈ ‚ Ï˚Î¸ÌÓÈ ‚Ó‰Â. ê‡ÒÚ‚ÓËÚÂÎË (·ÂÌÁËÌ,

ÒÔËÚ, ‡ÏÏË‡Í Ë Ú. ‰.) ÔËÏÂÌﬂÚ¸ Á‡ÔÂ˘‡ÂÚÒﬂ, Ú. Í.

ÓÌË ÏÓ„ÛÚ ÔÓ‚Â‰ËÚ¸ ÔÎ‡ÒÚÏ‡ÒÒÓ‚˚Â ‰ÂÚ‡ÎË.

ëÏ‡ÁÍ‡

å‡¯ËÌ‡ ÌÂ ÚÂ·ÛÂÚ ÒÏ‡ÁÍË.

çÂËÒÔ‡‚ÌÓÒÚË

Ç ÒÎÛ˜‡Â ÌÂËÒÔ‡‚ÌÓÒÚË, Ì‡ÔËÏÂ, ‚ÒÎÂ‰ÒÚ‚ËÂ

ËÁÌÓÒ‡ ‰ÂÚ‡ÎË, Ó·‡˘‡ÈÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm.

Ç ÍÓÌˆÂ Ì‡ÒÚÓﬂ˘Â„Ó ÛÍÓ‚Ó‰ÒÚ‚‡ ËÏÂÂÚÒﬂ

ËÎÎ˛ÒÚ‡ˆËﬂ ÒÓÒÚ‡‚‡ Ï‡¯ËÌ˚, ÔÓÍ‡Á˚‚‡˛˘‡ﬂ

‰ÂÚ‡ÎË, ÍÓÚÓ˚Â ÏÓ„ÛÚ ·˚Ú¸ Á‡Í‡Á‡Ì˚.

áÄôàíÄ éäêìÜÄûôÖâ ëêÖÑõ

ÑÎﬂ ÔÂ‰ÓÚ‚‡˘ÂÌËﬂ ÔÓ‚ÂÊ‰ÂÌËﬂ ‚Ó ‚ÂÏﬂ

Ú‡ÌÒÔÓÚËÓ‚ÍË Ï‡¯ËÌ‡ ÔÓÒÚ‡‚ÎﬂÂÚÒﬂ ‚ ÔÓ˜ÌÓÈ

ÛÔ‡ÍÓ‚ÍÂ. ÅÓÎ¸¯ËÌÒÚ‚Ó ˝ÚËı ÛÔ‡ÍÓ‚Ó˜Ì˚ı

Ï‡ÚÂË‡ÎÓ‚ ÏÓ„ÛÚ ·˚Ú¸ ÛÚËÎËÁËÓ‚‡Ì˚. èÓÒËÏ

Ò‰‡Ú¸ Ëı ‚ ÔÛÌÍÚ˚ ÔËÂÏ‡ ‚ÚÓË˜ÌÓ„Ó Ò˚¸ﬂ.

ëÚ‡‚¯ËÈ ÌÂÌÛÊÌ˚Ï ËÌÒÚÛÏÂÌÚ ÔÓÒËÏ Ò‰‡Ú¸

ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm. éÌ ·Û‰ÂÚ ÛÚËÎËÁËÓ‚‡Ì

˝ÍÓÎÓ„Ë˜Ì˚Ï ÏÂÚÓ‰ÓÏ.

ÉÄêÄçíàü

ìÒÎÓ‚Ëﬂ „‡‡ÌÚËË ÒÓ‰ÂÊ‡ÚÒﬂ ‚ ÓÚ‰ÂÎ¸ÌÓÈ

„‡‡ÌÚËÈÌÓÈ Í‡ÚÓ˜ÍÂ.

àÁ„ÓÚÓ‚ËÚÂÎ¸ Á‡ﬂ‚ÎﬂÂÚ, ˜ÚÓ ·ÂÂÚ Ì‡ ÒÂ·ﬂ

ËÒÍÎ˛˜ËÚÂÎ¸ÌÛ˛ ÓÚ‚ÂÚÒÚ‚ÂÌÌÓÒÚ¸ ‚ ÚÓÏ, ˜ÚÓ ËÁ‰ÂÎËÂ

ÒÓÓÚ‚ÂÚÒÚ‚ÛÂÚ ÒÎÂ‰Û˛˘ËÏ ÒÚ‡Ì‰‡Ú‡Ï ËÎË

ÌÓÏ‡ÚË‚Ì˚Ï ‰ÓÍÛÏÂÌÚ‡Ï

EN50144-1, EN50144-2-11, EN55014-1,

EN55014-2, EN61000-3-2, EN61000-3-3

Ë ÚÂ·Ó‚‡ÌËﬂÏ ‰ËÂÍÚË‚.

89/392/EEC,

73/23/EEC,

89/336/EEC

ÓÚ 04-12-2002

ÉÂÌÂÏÓÈ‰ÂÌ,

çË‰ÂÎ‡Ì‰˚

W. Kamphof

éÚ‰ÂÎ ÍÓÌÚÓÎﬂ Í‡˜ÂÒÚ‚‡

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ ВЕЛИКОБРИТАНИЯ

(

)

44 Ferm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FRS 600 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FRS 600 Manual

Product: