Manual Ferm FRS 600 (page 3 of 24) (English, German, Dutch, Danish, French, Italian, Norwegian)

110162

Zoom out

Zoom in

1/24

46 Ferm

SPARE PARTS LIST FRS-600

REF NR DESCRIPTION FERM NR

001 ADJUSTABLE BOTTOM PLATE 408500

002 GUARD PLATE 408501

003 RUBBER SLEEVE 408502

007 BLADE HOLDER 408503

014 RECIPROCALING BAR 408504

015 SLIDING BEARING 408505

019 ADJUSTING SPEED PLATE 408506

021 large cover sheet 408507

024 ROLLER BEARING 408508

027 ROLLER SHAFT 408509

028 GEAR WHEEL 408510

029 WASHER 408511

030 CENTRE COLUMN 408512

032 CARBON BRUSH SET 408513

033 CARBON BRUSH HOLDER 408514

037 SWITCH 408515

052 ROTOR 408516

057 STATOR 408517

RECIPROCATING SAW

THE NUMBERS IN THE FOLLOWING TEXT COR-

RESPOND WITH THE PICTURES AT PAGE 2

TECHNICAL SPECIFICATIONS

PRODUCT INFORMATION

Fig.A

1. Blade

2. F ootplate

3. Blade clamp screw

4. Trigger switch

5. Speed controller

6. Trigger lock button

7. Mains lead

8. Footplate length adjustment screws

9. 3 mm hexagon key (not s hown)

10. 4 mm hexagon key (not shown)

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of the

instructions in this manual.

Denotes risk of electric shock.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Keep these instructions in a safe place!

ADDITIONAL SAFETY INSTRUCTIONS

The machine must not be damp and must not be

operated in a wet environment. Always inspect

cable and plug before using machine. Only have

damage repaired by a qualified professional.

Only insert the plug into the mains socket when the

machine is switched off. Wear protective gloves and

sturdy footwear.

Do not saw materials containing asbestos!!!

• Wear protective goggles when working with mate-

rials which produce large amounts of chips.

• Wear a protective mask when sawing other fibrous

materials.

• Portable equipment used outdoors must be connec-

ted with a fault-current circuit breaker.

• Extension cables and plugs must be approved for out-

doors.

• Remove adjusting keys and wrenches before turning

the tool on.

• Secure your workpiece with clamps. Always lead

cable away from machine towards the rear.

• Move machine towards the workpiece only when

switched on.

• Always hold machine with both hands and ensure

that you have a safe footing while working.

• The machine may be operated only with the foot

plate mounted. When sawing, the foot plate must

always rest on the workpiece.

• Always remove the plug from the mains socket

before carrying out any work on the machine.

• Do not carry the machine by the cable.

• Incorrect handling may damage the machine. There-

fore always comply with the following instructions.

• Use only sharp saw blades in perfect condition;

replace cracked, distorted or blunt saw blades imme-

diately.

• Machine should only be switched on with blade

installed

• Select tools, stroke rate and pendulum actions

according to material, Take care to maintain a con-

stant reed rate.

• Do not attempt to stop the saw blade with lateral

pressure after switching off.

• Only use genuine accessories.

• Always use the correct supply voltage. The voltage

specifications on the rating plate must correspond

with the mains voltage. Equipment marked with 230

V can also be connected to 220-240 V.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Excessive sparking of the carbon brushes and vertici-

liosis in the collector.

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defect switch.

• Smoke or stench of scorched insulation.

Voltage | 230 V~

Frequency | 50 Hz

Power input | 600 W

No load speed | 300-2000/min

Maximum cutting thickness | 115 mm

Stroke length | 30 mm

Weight | 3.3 kg

Lpa (sound pressure level) | 86 dB(A)

Lwa (sound pressure capacity) | 99 dB(A)

Vibration value | 8.9 m/s

English

Ferm 3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FRS 600 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FRS 600 Manual

Product: