110130
9
Zoom out
Zoom in
Previous page
1/56
Next page
Ferm 09
Using the machine
Use clamps or a vice to hold the work.
Never remove wood chips and saw dust that is close to the saw blade with your hands. If
there are small pieces of wood left between the fixed and the movable parts, the circular
saw will have to be stopped. The plug needs to be removed from the socket, before any left
piece can be removed.
Check that the blade is suitable for the spindle speed of the circular saw. Do not attempt to
cut before the circular saw has reached full speed. Make sure the circular saw runs without
load (i.e. is not in contact with the work) when you switch it on. The circular saw must have
reached its full speed first.
Never cut wood that is thicker than the depth of the saw blade.
When cutting in wooden walls or floors, check there is no wiring or piping where you intend
to cut.
Switch off the tool and wait until the blade has stopped completely before moving the saw
away from the work or putting it down. Hearing protection should be worn when using
circular saw.
Switch off the machine immediately when you discover:
A defective mains plug or mains lead;
A defective switch.
Overheating of the circular saw.
Smoke or odeur caused by scorched insulation.
Electrical safety
When using electric machines always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions and also the enclosed safety instructions. Keep these instructions in a
safe place!
Always check that the power supply corresponds to the voltage on the rating
plate.
The machine is double insulated; therefore no earth wire is required.
Replacing cables or plugs
If the mains cable becomes damaged, it must be replaced with a special mains cable
available from the manufacturer or the manufacturer
s customer service. Dispose of old
cables or plugs immediately after replacing them with new ones. It is dangerous to con-
nect the plug of a loose cable to a socket.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The mini-
mum conductor size is 1.5 mm
2
. When using a cable reel always unwind the reel completely.
GB
D
NL
F
E
P
I
S
SF
N
DK
104 Ferm
3. MONTAGE OG INDSTILLINGS FORSKRIFTER
Inden indstillingen af rundsaven påbegyndes, skal du forvisse dig om, at stik-
ket er trukket ud af stikkontakten.
Indstilling af savevinkel (skråvinkel)
Fig. B
Løsn begge knapper (1).
Drej bundpladen i den korrekte position (0° - 45°) og stram knapperne igen.
Savevinklen (skråvinkel) kan aflæses på vinkelmåleren (2).
Montering af kløveanlægsfladen
Fig. B
Løsn knappen (3).
Sæt kløveanlægsfladen i de forhåndenværende spalter (4).
Indstil den korrekte skærebredde og stram knappen igen (3).
Indstilling af skæredybde
Fig. C
Løsn knappen (1).
Før bundpladen (2) nedad.
Savklingens skæredybde kan aflæses på siden af sikkerhedsskærmen.
Stram spændeknappen (1) igen, når den korrekte dybde er indstillet.
Udskiftning eller rengøring af savklingen
Fig. D
Brug aksellåseknappen (2) for at forhindre akslen i at dreje.
Løsn derefter sekskantskruen (3) midt i savklingen, med den medfølgende sekskantnøgle.
Drej sikkerhedsskærmen tilbage, og hold den der ved hjælp af knappen (1).
Træk stopringen og savklingen ud og gør savklingen ren eller udskift den med en ny.
Sæt igen savklingen tilbage på akslen. Sørg for at savklingens tænder peger i samme
retning som spaltekniven (4).
Sørg for, at delekniven indstilles således, at
Afstanden mellem den og tænderne på savklingen ikke er over end 5 mm.
Tænderne på savklingen ikke stikker mere end 5 mm frem foran underkanten af
delekniven.
Delekniven skal altid bruges, undtagen når der saves ind i midten af arbejdsemnet.
Lad sikkerhedsskærmen vende tilbage over savklingen ved at løsne knappen (1).
Tryk aksellåseknappen (2) i igen, monter stopringen (5) igen og stram sekskantskruen
godt igen.
4. BETJENING
Det anbefales at bruge høreværn, når der arbejdes med rundsaven.
UK
D
NL
F
E
P
I
S
SF
N
DK
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FKS 185 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info