Manual Ferm FKS 185 L (page 7 of 56) (English, German, Dutch, Danish, French, Italian, Norwegian)

110130

Zoom out

Zoom in

1/56

Ferm 07

Danger

a) Keep hands away from cutting area and the blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are holding the saw

, they cannot be cut by the blade.

b) Do not reach underneath the workpiece. The guard cannot protect you from the blade

below the workpiece.

c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade

teeth should be visible below the workpiece.

d) Never hold piece being cut in your hands or across your leg. Secure the workpiece to a

stable platform. It is important to support the work properly to minimize body exposure,

blade binding, or loss of control.

e) Hold power tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also

make exposed metal parts of the power tool "live" and shock the operator.

f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of

cut and reduces the chance of blade binding.

g) Always use blades with correct size and shape (diamond versus round) of arbour holes.

Blades that do not match the mounting hardware of the saw will run eccentrically, causing

loss of control.

h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were

specially designed for your saw, for optimum performance and safety of operation.

Causes and operator prevention of kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back toward the operator;

•

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade

can dig into the top surface of the wood causing the blade to climb out of the kerf and jump

back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below.

a) Maintain a firm grip with both hands on the saw and position your arms to resist kickback

forces. Position your body to either side of the blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but kickback forces can be controlled by the

operator,if proper precautions are taken.

b) When blade is binding, or when interrupting a cut for any reason, release the trigger and

hold the saw motionless in the material until the blade comes to a complete stop. Never

attempt to remove the saw from the work or pull the saw backward while the blade is in

motion or kickback may occur. Investigate and take corrective actions to eliminate the

cause of blade binding.

c) When restarting a saw in the workpiece, centre the saw blade in the kerf and check that

saw teeth are not engaged into the material. If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of blade pinching and kickback. Large panels

tend to sag under their own weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

106 Ferm

Rengøring

Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til

at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammo-

niak, osv

. Den slags stoffer beskadiger kunststofdelene.

Udskiftning af kulbørster

Fig. E

• Fjern skruerne (1).

•

Træk kulbørsterne (2) ud fra rundsaven og undersøg dem for slitage.

• Sæt kulbørsterne tilbage i de forhåndenværende holdere.

• Kontroller, at kobberkontakten på kulbørsterne er i god kontakt med kobberdelen i

børsteholderen.

• Sæt skruerne (1) i igen og stram dem godt.

Efter mange driftstimer kan kulbørsterne være slidt. Derfor skal kulbørsterne

kontrolleres regelmæssigt efter hver 30 driftstimer

. Hvis kulbørsterne er kortere

end 4 mm, skal de udskiftes med nye.

Smøring

Maskinen behøver ingen ekstra smøring.

• Elektromotoren over-

ophedes.

• Maskinen virker ikke,

selv om den er tilko-

blet.

• Det er vanskeligt at

føre arbejdsemnet i en

ret linie langs savklin-

gen og savskæret er

uregelmæssigt.

• Rundsaven støjer

og/eller går meget ure-

gelmæssigt.

• Motoren overbelastes,

fordi der saves for

store arbejdsemner.

• Motoren er defekt.

• Fejl i netledningen.

• Afbryderen er defekt.

• Savklingen er bøjet

eller sløv.

• Kulbørsterne er slidte.

• Sav i et lavere tempo

og lad motoren køle af.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Kontrollér netledningen

for brud.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Udskift savklingen.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 62 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FKS 185 L Manual

Product: