110130
10
Zoom out
Zoom in
Previous page
1/56
Next page
Ferm 103
Blokér ikke den bevægelige beskyttelseskappe i åben stilling.
Vær ved savning af træ opmærksom på knaster, søm, revner og/eller aflejring af
smuds. Savning af dette træ kan føre til den farlige situation, at rundsaven løber fast.
Efterlad aldrig rundsaven uden tilsyn.
Brug maskinen udelukkende til savning af træ.
Når rundsaven er i brug
Arbejdsemnet skal klemmes godt fast.
Trærester eller lignende, der er i umiddelbar nærhed af saven, må ikke fjernes med
hånden. Når trærester har sat sig fast mellem faste og/eller bevægelige dele, skal
maskinen stoppes og netstikket trækkes ud af stikkontakten, før træresterne fjernes.
Sørg for, at rundsaven tilkobles ubelastet. (Undlad at rundsaven kommer i kontakt
med arbejdsemnet, når den kobles til). Rundsaven skal først have nået det maksima-
le omdrejningstal.
Sav ikke arbejdsemner, der er tykkere end savens dybde.
Forvis dig om, at der ikke er elektriske kabler, vandrør eller gasledninger, når du
saver i vægge eller gulve.
Sluk først for rundsaven og vent til savklingen er kommet helt til stilstand, før du fjer-
ner rundsaven fra arbejdsemnet og lægger maskinen til side.
Maskinen skal slukkes øjeblikkeligt, når:
Stikket eller netledningen er defekt, eller hvis ledningen er beskadiget.
Afbryderen er defekt.
Rundsaven er overophedet.
Der er røg eller det lugter af svedet isolationsmateriale.
Elektrisk sikkerhed
Ved anvendelse af elektriske mas kiner skal man altid følge de lokalt gældende sikker-
hedsforskrifter i forbindelse med brandfare, fare for elektrisk stød og legemensbeskadigel-
se. Læs udover de nedenstående instruktioner også sikkerhedsforskrifterne i den separat
vedlagte sikkerhedsfolder. Bevar instruktionerne godt!
Kontroller altid om netspændingen svarer til værdien på typeskiltet.
Maskinen er dobbeltisoleret; det er derfor ikke nødvendigt med en jordledning.
Udskiftning af ledninger eller stik
Hvis netledningen er blevet beskadiget, skal den udskiftes med en speciel netledning, som kan
fås via fabrikanten eller fabrikantens kundeservice. Gamle ledninger og stik skal kasseres, når
de er blevet udskiftet med nye. Det er farligt at sætte stikket på en løs ledning i en stikkontakt.
Ved brug af forlængerledninger
Brug udelukkende godkendte forlæn gerledninger, der er beregnede til maskinens effekt.
Lederne skal have et gennemsnit på mindst 1.5 mm
2
. Hvis forlængerledningen sidder på
en tromle, rulles ledningen helt af.
UK
D
NL
F
E
P
I
S
SF
N
DK
10 Ferm
3. ASSEMBLY AND ADJUSTING INSTRUCTIONS
Before adjusting the saw, make sure the plug is removed from the socket.
Setting the sawing angle (bevel)
Fig. B
Loosen both knobs (1).
Rotate the soleplate to the correct position (0° - 45°), and tighten the knobs. The
sawing angle (bevel) can be read on the protractor (2).
Fitting the ripfence
Fig. B
Loosen knob (3).
Insert the rip fence into the slots provided (4).
Set the correct cut width and tighten the knob (3).
Setting the cutting depth
Fig. C
Loosen knob (1).
Move the soleplate (2) downwards.
The cut depth of the saw blade can be read off on the side of the safety guard.
Tighten the clamping knob (1) once the correct depth is set.
Exchanging or cleaning the saw blade
Fig. D
Use the shaft locking knob (2) to prevent the shaft from rotating.
Next loosen the hexagon screw (3) in the centre of the saw blade, using the
Allen key
provided.
Turn the safety guard to the rear, and hold it there with the aid of the knob (1).
Withdraw the retaining ring and the saw blade, and clean the saw blade, or replace it
with a new one.
Again place the saw blade back on the shaft. Ensure that the teeth of the saw blade
are pointing in the same direction as the riving knife (4).
Ensure that the splitting wedge is set in such a way that
The gap between it and the toothed wheel rim of the saw blade does not exceed
5 mm
And that the toothed wheel does not protrude more than 5 mm beyond the lower
edge of the splitting wedge.
The splitting wedge must always be used except when cutting into the middle of the
workpiece.
Allow the safety guard to return over the saw blade by releasing the knob (1).
Press the shaft locking knob (2) back in, refit the retaining ring (5) and tighten the
hexagon screw firmly once more.
GB
D
NL
F
E
P
I
S
SF
N
DK
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FKS 185 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info