78863

Ferm FDCD 1440 K2 Manual

7
Zoom out
Zoom in
Previous page
1/48
Next page
Ferm
• Når du slipper startknappen (1), bliver patronen straks bremset, og der er ikke noget
efterløb.
• Når maskinen er slukket, kan du blokere den ved at sætte knappen for
omløbsretningen (6) i den midterste position.
Læg først maskinen fra dig når motoren står helt stille. Læg ikke maskinen på et støvet
underlag. Der kan trænge støv ind i mekanismen.
Opladning af batterier
Det vedlagte batteri er ikke opladet ved leveringen.
•
Brug kun batteriopladeren ved temperaturer mellem +5 ºC. og + 40 ºC.
• Brug kun batteriopladeren i tørre, udluftede lokaler.
Opladning
Fig. F
• Sæt batteriholderen på et plant bord og sæt batteriet i batteriholderen. Vær
opmærksom på markeringerne af + og - pol.
•
Sæt netadapterens adapterstik i stikket på siden af batteriholderen.
• Sæt netadapteren i stikkontakten.
• Den røde opladningslampe på batteriholderen lyser for at vise, at batteriet er ved at
blive opladet.
• Opladningen af et helt afladet batteri tager cirka 5 timer første gang og derefter cirka 3
timer.
Det røde lys slukkes ikke automatisk, når opladningstiden er forbi! Tag
batteriet ud af opladeren inden 5 timer
. Hvis batteriet ikke tages ud af
opladeren efter opladningstiden, kan det blive overophedet.
Afladning af batteriet
Det er ikke kun opladningen af batterierne, der er vigtig, afladningen har lige så
stor eller måske endnu større betydning.
• Når batteriet er opladet, skal akku-boremaskinen bruges, indtil du begynder at lægge
mærke til, at boremaskinens kraft er i aftagende, og at den ikke når op på den
maksimale omdrejningshastighed.
•
Batteriet er nu næsten afladet. Først nu kan du begynde at lade batteriet op.
• Hvis batteriet oplades, mens det stadig er opladet til f.eks. en tredjedel af kapaciteten,
kan den såkaldte ‘hukommelseseffekt’ forekomme. Da det under opladningen nu kun
er den afladede del af batteriets batterikapacitet, der oplades, kan batteriet begynde at
krystallisere i den tredjedel, der stadig er opladet. Denne del af batterikapaciteten kan
aldrig bruges bagefter.
• Aflad ikke batteriet til minimum. Så snart du bemærker, at styrken eller den maksimale
omdrejningshastighed begynder at tage af, skal batteriet oplades. Når du fortsætter
med at bruge boret, og batteriet bliver helt afladet, kan den såkaldte ‘ombyttede poler’-
effekt forekomme.
90
GB
D
NL
F
E
P
I
S
FIN
N
DK
Ferm 7
15. Never throw the battery block onto a fire or into water. This will risk explosion!
Electrical safety
Always check that the voltage on the batterypack corresponds to the voltage
on the rating plate.
Also check that your mains voltage corresponds to the input
voltage of the battery charger.
The battery charger is double insulated in accordance with EN60335; therefore
no earth wire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones.
It is dangerous to insert the plug of a loose cable in the wall outlet.
•
Remove the battery block. When the power tool is not being used, prior to
maintenance and when changing tools such as the clamping chuck, and drill.
• The tool is suitable for use as a screwdriver and drill. Any other application is
specifically excluded.
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always remove the battery.
Fitting and removing drill cutters
Fig. B
In addition to drill cutters, the tool can also accommodate screwdriver bits with a
hexagonal shaft.
• Loosen the drill chuck (4) by rotating the hand-grip (9).
• Insert the shaft of the drill cutter into the chuck.
• Tighten the drill chuck so that the drill cutter is firmly clamped.
•
Rotate the drill chuck in the opposite direction when you wish to change the cutter.
Connecting and removing the battery
Fig. C
Ensure that the exterior of the battery block or tool is clean and dry before
connecting the charger.
• Ensure that the direction reversing switch (6 Fig. A) is in the central position in order to
prevent the appliance from being switched on unexpectedly
.
GB
D
NL
F
E
P
I
S
FIN
N
DK
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FDCD 1440 K2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDCD 1440 K2 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info