Manual Ferm FDCD 1440 K2 (page 8 of 48) (English, German, Dutch, Danish, French, Italian, Norwegian)

78863

Zoom out

Zoom in

1/48

Ferm 89

4. BETJENING

Overhold altid sikkerhedshenvisningerne, og følg de relevante forskrifter.

Hold maskinen ordentligt fast, og tryk boret ensartet ind i emnet. Undgå at overbelaste

maskinen. Anvend udelukkende bor som ikke udviser synligt slid. Slidte bor har en negativ

indflydelse på maskinens funktionsevne.

Indstilling af hastigheden

Fig. D

Maskinen har to borehastigheder.

•

For at bore langsomt eller bruge maskinen som

skruetrækker skal du sætte hastighedsomskifteren (2) i position '1'.

• For at bore hurtigt skal du sætte hastighedsomskifteren i position '2'.

Der må ikke skiftes om, mens motoren kører!

Indstilling af drejningsmoment

Fig. E

Maskinen har 16 forskellige indstillinger for drejningsmoment til regulering af den kraft

hvormed skruer bliver skruet i eller ud.

• Sæt indstillingsringen for drejningsmoment (3) i den ønskede position.

De indstillinger af drejningsmomentet der er til rådighed, vises på indstillingsringen

dels med cifrene fra 1 til 8, dels med prikker mellem cifrene som angiver

mellempositioner (dvs. i alt 16).

• Man skal helst vælge den laveste position der giver tilstrækkelig kraft til at dreje

skruen rundt. Vælg en højere position hvis motoren "glider i koblingen".

Anvendelse som skruetrækker.

• Sæt knappen for omløbsretningen (6) i position 'R' for at skrue skruer i.

•

Sæt knappen for omløbsretningen (6) i position 'L' for at skrue skruer ud.

Boring

• Drej indstillingsringen for drejningsmoment (3) i boreposition.

Sørg for at knappen for omløbsretningen (6) altid står i position 'R' når du

borer

Start og stop

Fig. A

• Tryk på startknappen (1). Du kan regulere maskinens omdrejningstal ved at trykke

mere eller mindre hårdt på knappen.

FIN

Ferm

• Insert the battery (5) into the base of the appliance, as shown on the illustration. Push

the battery until it latches in.

• Press the locking buttons (10) on both sides before removing the battery, and

disengage the battery from the base of the appliance.

4.OPERATION

Always follow the safety notes and the relevant safety code.

Hold the appliance firmly and press the drills steadily onto the workpiece. Do not overload

the appliance. Only use drills with no visible wear

. Worn drills will have a bad effect on the

functioning of the appliance.

Adjusting the speed

Fig. D

The appliance has two drill speeds.

• For slow drilling or for driving or removing screws, set the speed selection switch (2)

to '1'.

• For fast drilling set the speed selection switch to '2'.

Never switch over when the motor is running!

Adjusting the torque

Fig. E

The appliance has 16 different torque settings with which to set the power for driving and

removing screws.

• Set the torque adjustment ring (3) to the desired position.

The available torque

settings are indicated on the adjustment ring by the numbers 1 to 8 and by dots

between the figures to define intermediate settings (16 in total).

• You should preferably choose as low a setting as possible when using the screwdriver.

Select a higher setting if the motor slips.

Driving and removing screws

• Set the direction reversing switch (6) to position 'R' in order to drive screws.

• Set the direction reversing switch to position 'L' in order to remove screws.

Drilling

• Rotate the torque adjustment ring (3) to the drilling position.

Ensure that the direction reversing switch (6) is always set to 'R' during drilling.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDCD 1440 K2 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FDCD 1440 K2 Manual

Product: