Manual Ferm FDCD 1440 K2 (page 9 of 48) (English, German, Dutch, Danish, French, Italian, Norwegian)

78863

Zoom out

Zoom in

1/48

Ferm 9

Switching the device on and off

Fig. A

• Depress the on/off switch (1). It regulates the speed of the appliance by transmitting

power to the switch.

•

Release the on/off switch (1) to halt the drill chuck immediately which will no longer

run on.

• Move the direction reversing switch (6) to the centre in order to lock the appliance in

its disabled state.

Only lay down the appliance when it has stopped running completely. Do not place it on a

dusty surface as particles of dust could get into the mechanism.

Charging the battery

The included battery is delivered in non-charged condition.

•

Only use the battery charger in a temperature range between +5 °C. to + 40 ºC.

• Only use the battery charger in dry, ventilated rooms.

Charging

Fig. F

• Place the battery holder on a flat table and put the battery in the battery holder. Pay

attention to + and - pole markings.

• Put the adapter plug of the net adapter in the connector on the side of the battery

holder.

•

Put the net adapter in the socket.

• The red charging lamp on the battery holder will illuminate indicating the battery is

being charged.

• The charging process of a fully discharged battery will take approximately 5 hours the

first time and afterwards approximately 3 hours.

After the charging time the red light will not switch off automatically! Remove

the battery within 5 hours from the charger

. If the battery is not removed from

the charger after the charging period it may become overheated.

Discharging the battery

Not only charging batteries is important, discharging is of equal importance or

even greater importance.

• When the battery is charged the cordless drill has to be used until you start noticing

that the power of the drill is diminishing and that the maximum rotational speed is not

reached.

•

The battery is almost discharged now. Only now you can start charging the battery.

• Charging the battery while it is still charged for say one-third of capacity, the so-called

‘memory effect’ can occur. Since during charging only the discharged part of the

battery capacity of the battery is being charged now, the battery can start crystallizing

in the one-third that is still charged. This part of the battery capacity can never be

used afterwards.

Ferm

Læs og overhold alle disse henvisninger før du anvender dette elværktøj.

Sikkerhedshenvisningerne skal opbevares ordentligt.

Tjek altid om batterispændingen svarer til den der er angivet på typeskiltet.

Tjek desuden om netspændingen svarer til batteriopladerens

indgangsspænding.

Opladeren er dobbeltisoleret i henhold til EN60335, så det er ikke nødvendigt

med jordforbindelse.

Udskiftning af kabler eller stik

Gamle kabler eller stik skal bortskaffes umiddelbart efter at de er blevet udskiftet med nye.

ilslutning af et stik med et løst kabel til en stikdåse er farligt.

• Tag batteriet af. Når elværktøjet ikke anvendes, før vedligeholdelse og ved udskiftning

af værktøjer som f.eks. borepatron og bor.

• Apparatet er egnet til skruning og boring. Enhver anden anvendelse er forbudt.

3. MONTAGE AF TILBEHØR

Fjern altid batteriet inden du begynder på arbejdet.

Isætning og udtagning af bor

Fig. B

Foruden bor kan man sætte skruetrækkerbits med sekskantet skaft i maskinen

•

Løsn borepatronen (4) ved at dreje på flangen (9).

• Sæt borets skaft ind i åbningen i borepatronen.

• Spænd borepatronen så boret sidder godt fast.

• Løsn borepatronen igen når du vil udskifte boret.

Isætning og udtagning af batteriet

Fig. C

Kontroller at den udvendige overflade på batteriet eller værktøjet er ren og tør,

inden du tilslutter opladeren.

• Sørg for at knappen til omløbsretningen (6 på fig. A) står i den midterste position, for

at undgå utilsigtet start af maskinen.

•

Sæt batteriet (5) ind i maskinens sokkel som vist på tegningen. Tryk det helt i bund så

det går i hak.

• For at fjerne batteriet skal du trykke låsekapperne (10) på begge sider ind og trække

batteriet ud af maskinens sokkel.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDCD 1440 K2 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FDCD 1440 K2 Manual

Product: