Manual Ferm FBF 1200 (page 8 of 96) (English, German, Dutch, Danish, French, Italian)

78982

Zoom out

Zoom in

1/96

the thumbwheel (13). Also during running the

rotational speed can be adjusted.

1 - 2 = low speed

3 - 4 = medium speed

5 - 6 = high speed

Max = maximum speed

The required speed depends of the material

and can be determined by practical testing.

Furthermore router bits with a large diameter

need a lower rotational speed.

Material Diameter Speed stages

router bit

Hardwood > 20 mm 1 - 2

10 - 20 mm 3 - 4

< 10 mm 5 - max

Softwood > 20 mm 1 - 3

10 - 20 mm 3 - 6

< 10 mm 5 - max

Aluminium > 15 mm 1

< 15 mm 1 - 2

Plastic > 15 mm 1 - 2

< 15 mm 2 - 3

After longer periods of working at low speed, allow

the machine to cool down by running it for a few

minutes at high speed with no load.

Height setting of the router column

Fig. G

Button (14) is used to set the maximum height of

the router.

The cutting depth is then fixed. This is usually

necessary when using the tool on a special router

table.

Rough setting:

Loosen the clamping lever (11). The router •

can then be pushed down against the spring

force.

Hold button (14) between your thumb and •

index finger.

Push the grey button (14) and use your other •

hand to push the router down at the same time.

Release the button. The router is now locked •

and will no longer return to its original position.

Fine adjustment:

Turn button (14) clockwise. This causes the •

router column to slowly move down.

Turn button (14) counter-clockwise. This •

causes the router column to slowly move up.

Setting of the cutting depth

Fig. G

The cutting depth can be adjusted by using

buttons 8, 9, 11 and 15. If the cutting depth is set

correctly, the groove in question can be routed

accurately to within 0.1 mm.

Preparation:

Place the desired cutter in the tool.•

Loosen the clamping lever (11). The router can •

then be pushed down against the spring force.

Push the tool down until the cutter touches the •

workpiece, then relock it using the clamping

lever (11).

Loosen button 9 (counter-clockwise).•

Set button 15 to zero.•

Use button 8 to set the depth all the way •

down.

Tighten button 9 (clockwise). The cutting •

depth is now set to precisely 0 mm.

Rough setting:

Read the value from the scale (12).•

Loosen button 9 (counter-clockwise).•

Turn button 8 and re-read the value from the •

scale. The difference between the two values

is the cutting depth setting.

For example: If the value on the scale (12)

is 8.5 in the zero-setting and the value is 7.0

after button (8) has been turned, then the

cutting depth has been set to 1.5 cm.

Retighten button 9 (clockwise).•

Fine adjustment:

Loosen button 9 (counter-clockwise).•

The top button (15) is still set to zero. Give this •

button a full counter-clockwise turn, until it is

back in the zero position. The cutting depth is

now 1.0 mm less.

If required, the cutting depth can be set •

accurately to within 0.1 mm.

Retighten button 9.•

Adjustment using the revolver- depth stop

The revolver-depth stop enables you to quickly

choose between six different cutting depths.

These are also determined by the adjustment of

the depth stop (10).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FBF 1200 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 19,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FBF 1200 Manual

Product: