78982

Ferm FBF 1200 Manual

6
Zoom out
Zoom in
Previous page
1/96
Next page
GB
6
8. Cutting depth adjustment button
9. Wing bolt for depth stop
10. Depth stop
11. Clamping lever
12. Cutting depth scale
13. Adjusting wheel for electronic speed controller
14. Height adjustment button
15. Cutting depth fine-tuning button
16. Dust extraction facility
17. Parallel fence ruler
18. Zero mark
19. Parallel fence
20. Guide rod
21. Depth stop revolver
2. SAFETY INSTRUCTIONS
Explanation of the symbols
Denotes risk of personal injury, loss of
life or damage to the tool in case of non-
observance of the instructions in this
manual.
Indicates electrical shock hazard.
The number of revolution of the
machine can be electronically set.
Wear ear and eye protection
The instructions must be kept in a safe place!
1. Please check workpieces for any obstructions
on the surface of the material, such as
protruding nails etc., to protect the router
head.
2. Wait until the router has come to a complete
stop before removing any blocked or routed
material around the cutter. Use a long stick for
this and not your finger.
3. Please keep your hands away from the
routing surface.
4. Immediately switch off the tool as soon as it
starts producing any unusual noise or starts
vibrating excessively.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is
double insulated; therefore no earthwire
is required.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
Immediately switch off the machine when:
Excessive sparking of the carbon brushes and •
verticiliosis in the collector.
Interruption of the mains plug, mains lead or •
mains lead damage.
Defect switch•
Smoke or stench of scorched isolation•
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
unplug the tool.
Wait until the machine has come to a
complete standstill and the cutter has
cooled down before replacing a cutter.
Mounting and removing cutters
Fig. B
Only use cutters with a shaft diameter which
corresponds with the size of the collet. Only use
cutters which are suited for the maximum speed
of the machine. The cutter diameter should not
exceed the maximum diameter (see ‘Technical
specifications’).
Press the spindle lock (7) and turn the collet •
nut (6) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FBF 1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FBF 1200 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 19,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info