78982

Ferm FBF 1200 Manual

7
Zoom out
Zoom in
Previous page
1/96
Next page
GB
7
Open the collet nut using the wrench.•
Place the cutter shaft in the collet.•
Tighten the collet nut so that the cutter is •
locked properly.
Open the collet nut when you want to replace •
a cutter.
Adjusting the parallel fence ruler
Fig. A+C
The parallel fence is a useful tool for precision
routing at a fixed distance from the edge of the
workpiece.
Place the desired cutter in the tool.•
Loosen the clamping lever (11).•
Push the tool down until the cutter sticks out •
from the base plate, then retighten the
clamping lever (11).
Place the router onto the workpiece in such a •
that the cutter touches the side of the
workpiece. Please ensure that the furthest
protruding part of the cutter touches the
workpiece (by turning the cutter if necessary).
Slide the provided guide rods (20) into the •
appropriate holes.
Slide the parallel fence onto the mounted rods •
until it is in full contact with the workpiece. The
zero-position is now set.
Attach the ruler (17) to the rod of the parallel •
guide. The zero on the ruler must be aligned
with the zero mark (18).
Loosen the parallel fence fixing screw (4) and •
move the fence until the desired setting has
been reached. Important: when adjusting the
parallel fence, please take into account the
diameter of the cutter.
Retighten the fixing screw (4).•
Mounting the guide bush
Fig. D
The guide bush is a handy aid for cutting a
pattern.
Mount the guide bush (23) on the router base •
(3) using the screws (22).
Mounting the adapter for dust extraction
Fig. E+F
Use the dust adapter for the extraction of dust.
Mount the dust adapter (24) with the screws •
(22) on the cutter sole (3).
Place the dust tube (25) in the dust output (16). •
Place the tube of your vacuum cleaner on the •
dust tube (25).
Keep the outlet of the machine behind
the machine for a good view on the
workpiece.
4. OPERATION
The on/off switch
Fig. A
To switch on the tool, press and hold the on/•
off switch (1).
If you release the on/off switch (1), the tool will •
be switched off.
Switch locking mechanism
You can lock the on/off switch by pressing the
on/off switch (1) and then button (5). The switch
lock can be released by briefly pressing the on/off
switch (1).
Always select a low speed for cutting
plastic workpieces.
Do not put the machine down when the motor is
still running. Do not place the machine on a dusty
surface. Dust particles may enter the mechanism.
Always observe the safety instructions
and applicable regulations.
Operation
Hold the machine in rest position on the workpiece
when switching the machine on or off. The cutter
in the collet may damage the workpiece.
Clamp the workpiece and make sure that the •
workpiece cannot slide from under the
machine during the cutting activities.
Hold the machine firmly and move it evenly •
over the workpiece. Do not force the machine.
Only use cutters which do not show any signs •
of wear. Worn cutters have a negative effect
on the efficiency of the machine.
Always switch off the machine first before •
removing the plug from the wall socket.
Speed preselection
The required speed can be preselected with
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FBF 1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FBF 1200 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 19,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info