Manual Ferm CSM1021 - KES-350 (page 10 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763360

Zoom out

Zoom in

1/64

Ferm 119

• Sæt den nye klinge ned i fæstet. Sørg for, at bladet sidder præcist i midten og at tænderne

peger i den rigtige omdrejningsretning. Den angives af pilene på siden.

NB.: Hvis klingen anbringes forkert kan det medføre blivende skade på maskinen.

• Anbring spænderingen over hullet og skru den fast, imod urets retning.

• Fjern den topnøgle, som klingen er blokeret med og drej den anden nøgle endnu mindst én

gang helt rundt for at være sikker på, at savklingen kan bevæge sig frit.

• Fjern den anden nøgle og sæt beskyttelseskappen tilbage på plads. Sørg for, at

beskyttelseskappen kan bevæge sig frit og ikke klemmer før maskinen tages i brug.

Justering af savdybden

Fig. 6

Savdybden kan justeres præcist i millimeter med savdybdeknappen. Dybdeskalaen angiver

hele millimetre med lange streger og halve millimetre med korte streger. For at indstille de hele

millimetere, skal du dreje justeringsknappen så langt, at tallet er helt synligt. For at få det bedste

resultat ved savning af træ og plastik, skal savdybdeinstillingen være lidt større end tykkelsen af

materialet. Ved savning af metal skal savdybden være 1,0 mm større end materialets tykkelse.

NB.: For at forekomme skader og ridser af det underliggende lag, kan der ved savning af træ eller

plastik indstilles en savdybde, der er lig med materialets tykkelse. Det kan dog medføre ru kanter.

NB.: Hvis justeringsknappen drejer med besvær, skrues den løs til gummipakningen bliver synlig.

Rengør det omkringliggende område med en blød børste og smør med et par dråber syntetisk olie.

Justering af længden

Fig. 7

For at kunne save pænt, er det vigtigt at vide, hvor savningen skal starte og slutte. På begge

sider at beskyttelseskappen er der tal, der stemmer overens med savdybdeindstillingen, for at

angive savklingens begyndelse og ende.

• Marker det område, der skal saves på materialet. Hvis det ikke er firkantet eller

rektangulært, skal begyndelses- og slutlinjerne angives. De skal altid trækkes lodret i

forhold til savlinjen.

• For at bruge længdeindstillingen, skal savdybden først indstilles som før beskrevet, f.eks.

9 mm. Find tallet, i dette tilfælde 9, på for- og bagsiden af beskyttelseskappen.

• Sørg for, at linjen under tallet stemmer overens med begyndelsespunktet på det stykke,

der skal saves ud.

• Sav indtil linjen under tallet på forsiden stemmer overens med slutpunktet på det stykke,

der skal saves ud.

Temperatursikring

Præcisionscirkelsaven er udstyret med en temperaturbegrænsning til forhindring af

overophedning. Når den bliver slået til, starter maskinen ikke før den er afkølet.

Når temperatursikringen aktiveres, stopper saven. Du kan først starte igen, når saven er kølet

af og stikket er taget ud af stikkontakten. Det kan tage 15 minutter.

Temperatursikringen aktiveres under følgende omstændigheder:

•Ved brug af stumpe savklinger

•Når der lægges for stor kraft i savningen

FIN

10 Ferm

Specific safety instructions

• Do not use misshaped or cracked blades.

• Regularly check the blades for damage. If necessary, replace them.

• Only use blades recommended by Ferm.

• Never use a saw that has components missing or a saw that is fitted with accessories which

were not supplied with the saw or which are not recommended for use with the saw.

• Never exert sideways pressure on the blade to bring it to a stop.

• Remove the plug from the plug socket before checking whether the protective cover can

move freely and does not become stuck.

• Do not lock or clamp the protective cover.

• Do not use the saw without the protective cover.

• Before using the saw, check whether the protective cover has been fitted.

• Always remove the plug from the plug socket before removing the protective cover,

replacing the blade or when checking the saw and carrying out maintenance work.

• Adamaged power cord should only be replaced by the manufacturer or a service agent.

• After use, the saw must be stored in such a way that the blade cannot become damaged.

Be careful at all times!

3. USE

Removing the protective cover

Fig. 2

•Make sure the plug has been removed from the plug socket.

• Unscrew the protective cover. Remove the cover.

N.B.: When replacing the protective cover, the blade can protrude from a groove in the base

plate. To prevent personal injury, keep body parts away from the blade. Make sure the

protective cover is replaced correctly.

Changing the blade

Fig. 3, 4, 5

• Remove the protective cover as described above.

• Use one of the Allen keys to lock the blade.

• Use the other Allen key to remove the blade by rotating the Allen key clockwise.

• Fit the new blade into the shaft. Make sure the blade sits exactly in the middle and the teeth

point in the correct direction. The direction is indicated by the arrows on the side of the saw.

N.B.: If the blade is fitted incorrectly, irreparable damage may be caused to the saw.

• Place the locking washer over the hole and screw it into place by rotating it anticlockwise.

• Remove the Allen key used to lock the blade and rotate the other Allen key at least one full

revolution to make sure the blade can move freely.

• Remove the second Allen key and replace the protective cover. Before using the saw,

make sure the protective cover can move freely and does not get stuck.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1021 - KES-350 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1021 - KES-350 Manual

Product: