Manual Ferm CSM1021 - KES-350 (page 11 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763360

Zoom out

Zoom in

1/64

Ferm 11

Adjusting the sawing depth

Fig. 6

The sawing depth can be accurately adjusted in millimetres using the sawing depth adjustment

knob. The long lines of the depth scale indicate whole millimetres and the short lines indicate

half millimetres.

To adjust the depth by whole millimetres, rotate the adjustment knob so that the whole number

is visible. For the best result when sawing wood and plastic, the sawing depth much be slightly

greater than the thickness of the material. When sawing metal, the sawing depth must be 1.0

mm greater than the thickness of the material.

N.B.: To prevent scratches or damage to the surface below, the sawing depth can be set to the

thickness of the material when sawing wood or plastic, but this can cause rough cutting edges.

N.B.: If it is difficult to rotate the adjustment knob, unscrew it until the rubber seal becomes

visible. Use a soft brush to clean the area around the seal and apply a few drops of synthetic oil

to it.

Adjusting the length

Fig. 7

In order to saw neatly, it is important to know where the saw must start and finish. There are

numbers on both sides of the protective cover which correspond to the sawing depth settings

and which indicate the start and finish points of the blade.

• Mark where the material is to be sawn. If the area to be sawn is not square or rectangular,

the start and finish lines must be indicated separately.These points must be drawn

perpendicular to the sawing line.

• In order to use the length setting, the sawing depth must first be set as described

previously. Set it to, for example, 9 mm. Find the number, in this case 9, at the front and

back of the protective cover.

• Make sure the line under the number is aligned with the starting point of the line to be sawn.

• Saw until the line under the number at the front of the cover is aligned with the end point of

the line to be sawn.

Temperature safety device

The Precision Circular Saw has a temperature limiting device for protecting the saw against

overheating. If this turns on, then do not start the saw before it has cooled down.

The saw will cut out when the temperature safety device is activated. The plug must then be

removed from the plug socket and you will only be able to restart the saw once it has cooled

down. It may take 15 minutes for the saw to cool down sufficiently.

The temperature safety device is activated in the following circumstances:

• When using blunt blades.

•If a too large force is exerted when sawing.

• Constant sawing of very hard or very thick material.

FIN

118 Ferm

c) Kontroller, at sikkerhedsanordningens plade til saven ikke rykker sig, når der udføres

"stiksavning", når indstillingen af savklingehældningen ikke er 90°. Sidelæns ændring af

klingen kan medføre, at den sidder fast, og man risikerer tilbageslag.

d) Sørg altid for, at sikringsanordningen dækker klingen, før du sætter saven ned på en bænk

eller på gulvet. En ubeskyttet savklinge med friløb kan medføre, at saven kører baglæns

og saver i hvad der nu måtte være på dens vej. Vær opmærksom på, at det tager lidt tid,

inden savklingen standser helt, efter der er slukket på kontakten.

Specifikke sikkerhedsforskrifter

• Brug ikke deforme eller knækkede savklinger.

• Kontroller regelmæssigt savklingerne for skader og udskift dem om nødvendigt.

• Brug kun savklinger, der er anbefalet af Ferm.

• Brug aldrig en ufuldstændig maskine eller en maskine, der er udstyret med tilbehør, der

ikke er leveret eller anbefalet.

• Udøv aldrig sidelæns tryk på savklingen for at få den til at stoppe.

• Kontroller om beskyttelseskappen kan bevæge sig frit og ikke klemmer. Tag først stikket ud

af stikkontakten.

• Bloker ikke beskyttelseskappen og klem den ikke fast.

• Brug ikke maskinen uden beskyttelseskappe.

• Kontroller altid først om beskyttelseskappen er sat på før brug.

• Tag altid stikket ud af stikkontakten før beskyttelseskappen fjernes, savklingen udskiftes

eller der udføres andre kontrol- eller vedligeholdelsesaktiviteter.

• En beskadiget ledning må udelukkende udskiftes af fabrikanten eller fabrikantens

serviceagenter.

•Efter brug skal værktøjet opbevares således, at savklingen er beskyttet godt.

Uanset hvad du gør – Vær forsigtigt!

3. ANVENDELSE

Aftagning af beskyttelseskappe

Fig. 2

• Sørg for, at stikket er taget ud af stikkontakten.

• Skru beskyttelseskappen løs. Fjern kappen.

NB.: Når beskyttelseskappen sættes tilbage på plads, kan savklingen stikke ud gennem en

fure i basispladen. Lad ikke legemsdele komme i berøring af den for at forhindre skader. Sørg

for, at beskyttelseskappen sættes rigtigt på plads.

Udskiftning af savklinge

Fig. 3, 4, 5

• Fjern beskyttelseskappen som beskrevet herover.

• Bloker savklingen med topnøglen.

• Skru klingen løs med den anden nøgle i urets retning.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1021 - KES-350 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1021 - KES-350 Manual

Product: