538650

Ferm CRM1030 FCO-2050 Manual

8
Zoom out
Zoom in
Previous page
1/50
Next page
Ferm 93
Udskiftning/påfyldning af olie
Kompressoren er leveret med syntetisk olie "SAE 10W30". Det er anbefalet at udskifte alt
pumpesystemets olie inden for de første 100 driftstimer.
• Skrue afløbsskruen (pakningen) af på beholderlåget, lad alt olien løbe ud og skrue skruen
på igen (fig. 17).
• Fyld olie på via det øverste hul på beholderlåget (fig.18) indtil måleinstrumentets indikation
på pakningen (fig. 8) er nået.
Check pumpensystemets olieniveauet hver uge, og fyld om nødvendigt. Den syntetiske olie
har den fordel at den ikke mister dens karakteristisk, hverken om sommeren eller om vinteren.
Du bør ikke hælde brugt olie ud i afløbet eller naturen.
Overhold venligst nedenstående tabel, ved udskiftning af olie.
Olietype Driftstimer
Kvalitetsolie SAE 10W30 100 eller 6 måneder
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Garantibetingelser er beskrevet på det separat vedlagte garantibevis.
GB
D
NL
F
E
P
I
S
FIN
N
DK
08
Ferm
Extension cables
Long supply lines, extensions, cable reels and similar cause voltage dips and may prevent the
motor from starting. Sluggishness makes starting difficult at low temperatures under freezing
point (0°C). Only use an extension cable with a plug and earth, so never use damaged or
flattened extension cables. Check whether the extension cable is in a good condition. For this
device the extension cable should have a diameter of at least 2.5 mm
2
(this applies to a
maximum length of 20 metres). Always unroll extension cables fully before using them.
Electrical connection
Always check whether the input voltage of the motor corresponds to the mains voltage
indicated on the specification plate. The compressors are supplied with an electrical cable and
a two-pole plug + earth. It is important to connect the compressor with an earthed plug socket.
(fig. 9)
Never use the earth-wire instead of the neutral (0-wire). The earthing should take
place in accordance with accident prevention regulations (EN 60204).
3. USE
For homehold use only
NB:The information you will find in this manual has been written to assist the operator in the use
and maintenance of the compressor. Some illustrations in this manual show details which may
differ from those of your compressor.
Installation
After having taken the compressor out of its packaging (fig. 1) and having checked that it is in
perfect condition, and having noted that no damage occurred during transport, the following
acts should be performed. If not yet fitted, fit the rubber feet on the tank according to the
instructions represented in fig. 2. Place the compressor on a flat surface or at a maximum slope
of 10° (fig.3), in a well ventilated area, protected against atmospheric factors and not in
explosive surroundings. If the surface area is sloping and smooth, make sure that the
compressor will not move when in operation. If the surface area is a board or a shelf of a
bookcase, just make sure that they cannot fall down by securing them properly. For proper
ventilation and effective cooling, it is important that the compressor is positioned at least 100
cm from the wall (fig. 4).
Make sure that the compressor is transported in the right way, do not turn it upside
down and don't lift it with hooks or ropes (fig. 5-6).
Important! Before commissioning
The carter of this compressor is filled with oil at the factory. To avoid leaking oil during transport,
there is a liquid-proof sticker stuck on the oil cap.
GB
D
NL
F
E
P
I
S
FIN
N
DK
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CRM1030 FCO-2050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1030 FCO-2050 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info