Manual Ferm CRM1030 FCO-2050 (page 10 of 50) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

538650

Zoom out

Zoom in

1/50

Ferm 91

Start

• Check om hovedspændingen stemmer overens med den som er indikeret på den

elektriske typeplade (fig. 10), den tilladte tolerance rækkevidde bør være inden for 5%.

• Tryk på knappen placeret på øverste del ind til “0” position, efter typen på trykregulatoren

monteret på enheden (fig. 11).

• Put stikket i stikkontakten (fig. 9), og start kompressoren ved at sætte knappen på

trykregulatoren i “I” position. Driften af kompressoren er totalt automatisk.

Trykregulatoren vil stoppe kompressoren når den maksimale værdi er opnået, og starte op

når trykket falder til under minimumværdien. Normalt er forskellen i tryk ca. 2 Bar/29 psi

mellem maksimum og minimum værdi. F.eks. - Kompressoren vil stoppe når den opnår 8

Bar (116 psi) (dette er det maksimale tryk ved drift), og vil automatisk starte op når trykket i

tanken er faldet til 6 Bar (87 psi).

Hovedet/cylinder/transmissionsrør kan opnå høje temperaturer, så hver forsigtig

når der arbejdes tæt på disse dele, og for at forebygge forbrændinger (fig. 12-13)

bør du ikke komme i kontakt med dem. «

Juster driftstrykket

Fig. 14

Det er ikke nødvendigt at anvende det maksimale driftstryk konstant, trykluftsværktøjet kræver

ofte mindre tryk. Ved kompressorer leveret med en trykreducerende ventil, er det nødvendigt

at indstille driftstrykket korrekt. Det er muligt at indstille driftstrykket ved at anvende

drejeknappen på reductionsventilen.

• Ved at dreje denne med uret, vil trykket øges.

• Ved at dreje denne mod uret, vil trykket mindskes.

Kompressoren har to trykmålere og to tilslutningspunkter for en trykluftslange:

• Venstre trykmåler: tryk på venstre udtag. Trykket på venstre udtag kan reguleres med

reduktionsventilen.

• Højre trykmåler: Tanktryk + tryk på højre udtag

Det indstillede tryk kan låses ved at dreje ringen under drejeknappen i den modsatte retning af

drejeknappen, herved fastlåses drejeknappen. Det indstillede tryk er synligt på trykmåleren på

reduktionsventilen.

4. FEJL

Lufttab

• Kan være forårsaget af en dårlig tætning af en forbindelse.

• Check alle forbindelser ved at væde dem med sæbe og vand.

Kompressoren køre men komprimere ikke

Fig. 19

•

Kan være forårsaget af ventilerne (C-C2) eller en pakning (B1-B2) som er ødelagt.

•

Udskift de ødelagte dele.

FIN

Ferm

The compressor runs but does not compress

Fig. 19

• May be caused by the valves (C-C2) or a gasket (B1-B2) being broken.

• Replace the damaged part.

The compressor will not start

If the compressor is difficult to start, check:

• whether the voltage of the mains corresponds to that on the specification plate (fig. 10)

• whether electrical extension cables are being used with a faulty core or length.

• whether the operating environment is too cold (below 0°C).

• whether there is oil in the sump to guarantee lubrication (fig. 8)

• whether there is electricity supply (plug properly connected, magneto-thermal fuses not

broken).

The compressor does not shut off

If the compressor does not shut off when the maximum pressure has been reached, the safety

valve of the tank will be activated. It is necessary to contact the nearest authorised Support

Service for the repair.

5.MAINTENANCE

Maintenance

Make sure that the plug is removed from the mains when carrying out maintenance

work on the motor.

The machines have been designed to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon proper machine care and

regular cleaning. Before interfering in any way whatsoever with the compressor, please make

sure that:

• The general line switch is in the "0" position.

• The pressure regulator and the switches on the switch board are switched off in the "0"

position.

• The air tank is fully decompressed.

Cleaning

Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

Lubrication

It is recommended to disassemble the suction filter every 50 operating hours and to clean the

filter element by blowing it with compressed air (fig. 15). It is recommended that the filter

element is replaced at least once a year if the compressor is working in a clean environment;

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1030 FCO-2050 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CRM1030 FCO-2050 Manual

Product: