Manual Ferm CDM1035 - FDC-2400lN (page 7 of 50) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763639

Zoom out

Zoom in

1/50

Ferm 07

14. If the battery pack is broken or can no longer be re-charged it must be properly disposed of.

15. Never throw the battery pack into water or a fire – it may explode.

Electrical safety

Warning! When using electric tools, basic safety precautions should always be followed to

reduce the risk of fire, electric shock and personal injury. Read all these instructions before

attempting to operate this product and save these instructions.

Always check that the voltage on the batterypack corresponds to the voltage on

the rating plate. Also check that your mains voltage corresponds to the input

voltage of the battery charger.

The machine is double insulated in accordance with EN60335; therefore no earth

wire is required.

Replacing cables or plugs

Immediately throw away old cables or plugs when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the wall outlet.

Prior to mounting an accessory always remove the battery.

Inserting and removing the drillbits

Fig. B

In addition to bits the machine can also hold screw bits with a hexagonal shaft.

• Loosen the chuck (7) by holding one section and turning the other.

• Position the drill bit shaft in the take up of the chuck.

• Fasten the chuck until the drill bit is tight.

• Open the chuck again when you want to exchange the drill bit.

Inserting and removing of the battery

Fig. C

• Make sure that the direction switch (1) is in middle position to prevent the machine from

switching on unexpectedly.

• Place the accumulator (3) in the bottom of the machine, as shown in the diagram, until it

engages.

• Before removing the accumulator, depress the release buttons (A) and then take the

accumulator out from the bottom of the machine

The drill must only be used with the forward / reverse switch fully enclosed

3. MOUNTING ACCESSORIES

94 Ferm

Vi erklærer herved, udelukkende på eget ansvar, at dette produkt opfylder følgende

standarder eller standardiserede dokumenter

EN50260-1, EN50260-2-1, EN50260-2-2, EN55014-1, EN55014-2,

EN60335-1,EN60335-2-29, EN61000-3-2, EN61000-3-3

i henhold til følgende direktiver:

98/37EEC, 73/23/EEC, 89/336EEC

01-10-2005

ZWOLLE NL

W. Kamphof

Quality department

Det er vores hensigt til stadighed at forbedre vores produkter, og vi forbeholder os derfor til

enhver tid retten til at ændre produktspecifikationerne uden forudgående varsel.

Ferm BV, Lingenstraat 6, 8028 PM , Zwolle, Holland

CE KONFORMITETSERKLÆRING (DK)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1035 - FDC-2400lN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CDM1035 - FDC-2400lN Manual

Product: