Manual Ferm CDM1035 - FDC-2400lN (page 9 of 50) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763639

Zoom out

Zoom in

1/50

Ferm 09

• For drilling in hard material like stone or concrete, rotate the impact sleeve (6) in anti-

clockwise until the indicator points at the mark ‘HAMMER’. In this case use a drill bit with

carbide tip.

Regular check the chuck for possible damage.

Possible use a coolant. In case of drilling in walls, watch out for drilling in electric

wires of water pipes. Get advice according to the use from your dealer.

Switching on and off

Fig. E

• Press the on/off switch (2) in. You regulate the speed of the machine by the degree to

which you keep the switch pressed in.

• Releasing the on/off switch (2) causes the drill to stop immediately

• Slide the direction switch (1) to the middle to lock the machine in switched off mode.

Do not put the machine away until the machine has completely stopped running. Do not store

the machine on a dusty surface. Dust particles can get into the mechanism.

Only operate the drill with the forward / reverse switch (2) fully engaged. Never

attend to use the drill with this switch in the neutral position.

Charging batteries

Fig. F

The enclosed battery charger has been exclusively designed for loading batteries of the FDC-

2400I.

• Position the battery (3) in the battery charger (9) as indicated in the illustration.

• Plug in the battery charger. The red “fast charging” light (10) is then illuminated

• As soon as the green light (11) is illuminated, charging has finished and the accumulator is

ready for use

Only use the battery charger in a dry environment at a temperature between 10 °C

and 40 °C.

The battery on the drilling machine you have purchased is not charged up. Before using it for

the first time leave it to charge for 1 - 2 hours in order for it to reach its full capacity. The total

capacity of the battery will be reached after it has been charged 4 – 5 times.

If the cordless drill is not going to be used for a long period of time, recharge the

battery before storing. From time to time recharge the battery for a short period of

time, to prevent it from running down. Store the battery separately in the plastic

case.

92 Ferm

Kontroller jævnligt borepatronen for beskadigelse.Brug eventuelt kølemiddel. Når

der bores i vægge, skal man passe på ikke at komme til at bore i ledninger eller

vandrør. Spørg forhandleren om råd vedrørende brug.

Tænd og sluk

Fig. E

• Tryk afbryderen (2) ind. Maskinens omdrejningshastighed kan reguleres ved at trykke

mere eller mindre på afbryderen.

• Når afbryderen (2) slippes, stopper maskinen straks.

• Sæt knappen til rotationsretning (1) i midterposition for at låse maskinen, så den ikke kan

tændes på afbryderen.

Læg ikke maskinen væk, før der er stoppet helt. Læg ikke maskinen på en støvet overflade.

Støvpartikler kan trænge ind i maskinen.

Brug kun maskinen, hvis knappen til rotationsretning (2) er helt i en af positionerne.

Brug ikke maskinen, hvis denne knap er i neutral position.

Opladning af batteri

Fig. F

Den medfølgende batterilader er kun beregnet til opladning af batterierne til FDC-2400 IN.

• Sæt batteriet (3) i batteriladeren (9) som vist på illustrationen.

• Sæt stikket til batteriladeren i en stikkontakt. Den røde lampe for “lynopladning” (10) lyser.

• Når den grønne lampe (11) lyser, er batteriet ladet op og klar til brug.

Batteriladeren må kun bruges i tørre rum ved en temperatur på mellem 10°C og

40°C.

Batteriet til denne boremaskine er ikke ladet op. Før maskinen bruges første gang, skal

batteriet lades op i 1 til 2 timer, så det når op på fuld kapacitet. Batteriets maksimale kapacitet

nås først, når det er blevet ladet op 4 til 5 gange.

Hvis accu boremaskinen ikke skal bruges i længere tid, skal batteriet lades op, før

det gemmes væk. Fra tid til anden skal batteriet lades en smule op, så man undgår,

at det aflades helt. Batteriet skal opbevares særskilt i plastickufferten.

Afladning af batteriet

Det er nødvendigt at lade batterierne op, men det er mindst lige så vigtigt, at det

aflades.

• Når batteriet er blevet ladet op, skal maskinen bruges, indtil man opdager, at maskinens

effekt begynder at blive mindre, så den ikke kan nå op på den maksimale

omdrejningshastighed.

• Nu er batteriet næsten afladet. Først nu skal man begynde at lade batteriet op.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1035 - FDC-2400lN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CDM1035 - FDC-2400lN Manual

Product: