Manual Ferm BSM1004 - FBS-1200 (page 7 of 42) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763823

Zoom out

Zoom in

1/42

Ferm 7

3. OPERATION

Always observe the safety instructions and applicable regulations.

Choice of the sand-paper

Coarse sand-paper (grain 50) removes in general the bigger part of the material and fine

sand-paper is used for the finishing. If the surface is not even, then start with rough sand-

paper. Further you use middle coarse sand-paper(grain 80) to remove the scratches left

behind by the coarse sand-paper and finally you take fine sand-paper (grain 120) for the

finishing.

Removing and Installing the sanding belt

Fig. C1 + C2

Before assembly the sanding belt always remove the plug from the mains.

• Put the machine on its side, with the drive belt cover down wards.

• Loosen the sanding belt fastener (4).

• Remove the sanding belt from the machine

• Put a new sanding belt on the machine, make sure that the direction arrows on the

sanding belt are pointing in the same direction as the direction indicator (5).

• Fasten the sanding belt fastener again (4).

Aligning the sanding belt

Fig. B

If the sanding belt doesn’t run parallel with the outer edge of the housing, the sanding belt

must be aligned. Move the sanding belt in the correct position with the adjusting knob (12).

By turning the adjusting knob clockwise the sanding belt will move to the inside and by

turning anti-clockwise the sanding belt will move to the outside.

Switching on and off

Fig. B

• To switch the machine on press the on/off switch (7).

• To switch the machine off release the on/off switch.

If continuous operation is required the blocking switch (8) must be used:

• Switch the machine on to press the on/off switch.

• Press the blocking switch and release the on/off switch.

• To switch the machine off press the on/off switch again and release the on/off switch.

FIN

Ferm

Mountering af støfpose

Fig. B

En komplet støvpose er vedlagt. Sæt en tråd-konsol (indeni støvposen) ind i adaptaren af

støvposen (når den ikke er monteret). Den bagerste del af konsollen skal peges opad.

Anvend støvposen for at samle støv op, som frigøres ved slibning med sandpapir.

• Sæt støvposen ind på støvopsamlerens åbning.

• Tøm støvposen regelmæssigt for at opnå en ordentlig støvsugning.

Maskinens støvpose adapter kan anvendes som kobling til en støvsuger.

Greb

Båndpudseren er nem at bruge på grund af de to håndtag, der er placeret henholdsvis

foran på siden af og bag på maskinen. Derved kan du holde maskinen med to hænder, så

du opnår en bedre kontrol med maskinen og undgår kontakt med de bevægelige dele.

Båndpudseren skal altid betjenes med begge hænder.

Betjening

Kontroller, at maskinen er oppe i fuld hastighed, før den anbringes på det emne, der skal

arbejdes på. Det forhindrer overbelastning af værktøjet.

Ved slibning af træ placeres maskinen ca. 15° fra træets fiberretning. Før båndpudseren

jævnt hen over det emne, der skal arbejdes på.

• Bøj ikke bånd sandpapiret.

• Anvend ikke det samme sandpapir for slibning af træ go metal.

• Tryk ikke for hårdt på maskinen, dette vil kun forhindre slibning med sandpapir.

4. VEDLIGEHOLDELSE

Sørg for at maskinen ikke står under strøm, når der udføres

vedligeholdelsesarbejder på mekanikken.

Disse maskiner er fremstillet til at fungere problemfrit i lang tid og med minimal vedligeholdelse.

Levetiden kan forlænges, hvis maskinen rengøres regelmæssigt og håndteres korrekt.

Fejl

For det tilfælde, at maskinen ikke fungerer korrekt, er herunder angivet en række mulige

årsager med tilhørende løsningsforslag:

• Udsædvanlig mange

gnister

• Dette tyder næsten altid

på tilstedeværelse af

smuds i motoren eller på

opslidte kulbørster.

• Få slibemaskinen

kontrolleret hos Deres

forhandler.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1004 - FBS-1200 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BSM1004 - FBS-1200 Manual

Product: