Manual Fender Princeton Sterio Chorus DSP (page 7 of 40) (English)

443094

Zoom out

Zoom in

1/40

PRINCETON CHORUS DSP - REAR PANEL

FCC COMPLIANCE NOTICE

A PRODUCT OF:

PRINCETON CHORUS DSP

A. IEC LINE CORD CONNECTOR - The line cord

must be connected to a grounded AC recepta-

cle in accordance with the voltage and frequen-

cy ratings as shown on the rear panel of the

amplifier ( {B}INPUT POWER ).

C. FOOTSWITCH - Plug-in connection for the

FOOTSWITCH (P/N 0055592000) for remote

switching of the Overdrive Mode, and both

DSP Effects circuits. NOTE: For proper opera-

tion of the FOOTSWITCH, the DRIVE SELECT

switch and both DSP Effects DEFEAT switches

on the front panel must all be OUT. (A speaker

grade cord is preferable to a coax guitar cord

for connecting the FOOTSWITCH.)

D. EFFECTS LOOP STEREO SEND - This jack

provides a line-level stereo output from the pre-

amp and both DSP Effects circuits of the

Princeton Chorus DSP. This output can be used

in conjunction with the {E}STEREO RETURN as

a patch point for external stereo effects devices.

(See “EFFECTS LOOPS - CONNECTION DIA-

GRAMS,” page 8) The EFFECTS LOOPS-

STEREO jacks are standard 1/4-inch

Tip-Ring-Sleeve types, with:

•Left channel signal on the Tip

•Right channel signal on the Ring

This send can also be used to feed a stereo sig-

nal to two channels of a recording or sound

reinforcement mixer. Additionally this output

can be used to drive another Princeton Chorus

DSP as a slave amplifier. This is done by con-

necting a shielded stereo cord from the

{D}STEREO SEND jack of the master ampli-

fier to the {E}STEREO RETURN jack of the

slave amplifier.

E. EFFECTS LOOP STEREO RETURN - This

stereo jack inputs signal directly to the left and

right power-amps. It automatically disconnects

the pre-amp and DSP Effects circuits when

used. This is useful when using the Stereo

E ffects Loop option, or when using the

Princeton Chorus DSP as a slave amplifier for a

stereo signal source.

F. EFFECTS LOOP MONO SEND - This jack pro-

vides an impedance-balanced mono output sig-

nal from the pre-amp at a point before the DSP

Effects circuits. This output can be used in con-

junction with the {G}MONO RETURN as a

patch point for external mono effects devices.

(See “EFFECTS LOOPS - CONNECTION DIA-

GRAMS,” page 8) The {F}MONO SEND can

also be used to send recording and sound rein-

forcement mixers a dry signal. Additionally this

output can be used to drive another Princeton

Chorus DSP as a slave amplifier. This is done

by connecting a standard guitar cord from the

{F}MONO SEND jack of the master amplifier to

the {G}MONO RETURN jack of the slave amplifier.

G. EFFECT LOOP MONO RETURN - This bal-

anced jack inputs signal to the stereo DSP

Effects circuitry, which drives the stereo power-

amp section. It automatically disconnects the

pre-amp signal when used. This is useful when

using the Mono Effects Loop option or when

using the Princeton Chorus DSP as a slave

amplifier for a mono signal source. The DSP

Effects are active in the slave amplifier so that a

true stereo image will be generated if the DSP

Effects are used. NOTE: In order to function

properly, a dummy plug or an extra guitar cord

must be inserted into INPUT 2 on the front

panel of the slave amplifier with its VOLUME

controls turned down.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC rules. These limits are designed to provide a re a-

sonable protection against harmful interf e r ence in a re s i d e n-

tial installation. This equipment generates, uses and can

radiate radio frequency energy and if not installed and used

in accordance with the instructions, may cause harm f u l

i n t e rf e r ence to radio communications. However, there is no

guarantee that interf e rence will not occur in a part i c u l a r

installation. If this equipment does cause harmful interf e r-

ence to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is

encouraged to try to correct the interf e rence by one or more

of the following measures: •Reorient or relocate the re c e i v-

ing antenna •Increase the separation between the equip-

ment and receiver •Connect the equipment into an outlet on

a circuit diff e rent from that of the receiver •Consult the deal-

er or an experienced radio/TV technician for help

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fender Princeton Sterio Chorus DSP in the language / languages: English as an attachment in your email.

The manual is 1,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fender Princeton Sterio Chorus DSP Manual

Product: