502512
13
Zoom out
Zoom in
Previous page
1/52
Next page
DECLARATION OF CONFORMITY
We hereby declare, under our sole responsibility,
that the FELISATTI brand products described in
this manual comply with the following standards or
standard documents: Standard EN 61029, Machine
Directive 98/37/EC and amendments, with 2006/95/
EC and 93/68/EEC, and in regard to electromagnetic
compatibility, with Directive 89/336/EEC, EN 55014.1,
EN 55014.2, EN61000.3.2 and EN 61000.3.3 and EN
50366.
Jordi Carbonell Santiago Lόpez
We reserve the right to make technical changes.
9 PROBLEMS-CAUSES-REMEDIES
PROBLEMS CAUSES REMEDIES
The motor fails to work Defective motor, power supply
cable or plug. Fuses blown
Have the machine checked by
pecialised personnel.
Never try to repair the motor
yourself because of the potential
danger involved.
Check the fuses and replace them
ifnecessary.
The motor starts slowly or does
not reachoperating speed.
Low power supply voltage.
Damaged motor windings.
Condenser burnt out
Have the voltage checked by the
power supply provider.
Have the motor checked by
specialised personnel.
Have the condenser changed by
specialised personnel.
Chipped or irregular cuts The blade is dull Sharpen or change the blade.
Step cut or irregular cutting
surfaces.
Inadequate blade
Worn-out or defective blade.
Replace the blade with a more
appropriateblade.
Change the blade.
MITRE SAW:
Cuts not made at the desired
angle.
Inadequate squaring. Clean the stroke-ends.
Adjust the turntable and the
stroke-ends.
UPPER TABLE:
Difculty in cutting.
Blade – splitting wedge out of
alignment.
Regulate the splitting wedge
and the protective casing xing
bracket.
Crooked trimming. The guide is not parallel to the
blade.
Align guide and blade.
Protective casings or moving
parts jammed.
Chips or dirt have not been
removed.
Perform a thorough cleaning by
spraying
compressed dry air.
The motor fails to start when the
starting button is pushed.
Switch malfunction.
Cables disconnected or broken.
Condenser malfunction.
Contact authorised Assistance
centers.
The blade stopping times lasts
longer than 10 seconds.
Electronic module malfunction. Contact authorised Assistance
centers.
13


Need help? Post your question in this forum.

Forumrules
1

Forum

felisatti-ntf305

Reset search

  • Hello,
    we need some parts of FELISATTI MT305S:
    - M Movable lower blade protector
    - K Machine lock knob 0°- 45°
    - L Turntable lock knob
    - S Upper table locking knob

    Where I can find these parts?
    I asked to some supplier but I didnt found them.
    Thank you Submitted on 22-6-2023 at 16:31

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti NTF305 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti NTF305 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info