Manual Felisatti NTF305 (page 11 of 52) (English, German, French, Italian, Spanish)

502512

Zoom out

Zoom in

1/52

WIDIA BLADES MATERIAL BLADE Ø – No. TEETH /min

WOOD

Ø 250 mm - Z 24 4500

Ø 250 mm - Z 40 4500

Ø 250 mm - Z 60 4500

Ø 305 mm - Z 72 4000

PVC Ø 250 mm - Z 60 4500

ALUMINIUM

Ø 250 mm - Z 60 4500

Ø 305 mm - Z 72 4000

FRAMES Ø 250 mm - Z 80 4500

does not provide shorter cutting times and can lead

to diminished efciency caused by the overloading of

the motor.

6.4.1 STARTING AND STOPPING THE BLADE

- Start the blade by pressing the tool lever A (g. 2)

and then wait until the blade reaches its maximum

rpm. - Lower the blade unit gradually and then

make the cut desired. After the cut has been made,

release the lever A (g. 2) and then wait until the

blade has come to a complete stop.

WARNING - Make sure that the movable protective

casings are all in correct position whenever the blade

is raised in rest position. The machine is provided

with a release button for the starting and stopping

of the blade. This button can be locked in “ON” by

pressing the switch black key B when the switch

black lever A is at the end of its stroke and the motor

is running (g. 2).

WARNING - This Lock in ”ON” button disables the

safety provided by the Manufacturer in the starting

lever switch. We recommend using this device only

with the greatest caution and only when the tool is

being used as a disk saw. In order to release the

switch, press the black lever A and then release it.

6.5 USING THE STROKE END RODS (g. 7)

Proceed as follows to use the stroke end rods: - Insert

the rod A in the hole of the workpiece support and lock

it in place with the corresponding knob B – Loosen

the knob C and adjust the rod D as required by the

length of the workpieces by using the millimetre ruler

for reference. Then lock the knob C back into position.

6.6 USING THE CLAMP (g. 8)

Proceed as follows to use the clamp:

- Insert the pin A in the corresponding slot B and lock

it in place with the dowel C located in the rear part of

the workpiece support

– Insert the clamp D on the pin A and lock it in place

at the desired height using the wing nut E

– Lock the piece to be cut into place by tightening

the upper knob F.

6.7 USING THE UPPER TABLE AS A DISK SAW

WARNING - The use of the upper table for the cutting

of steel and aluminium is absolutely prohibited.

- Never use the tool to make slots.

Proceed as follows to use the upper table: - Make

sure that the switch is not locked in “ON” - Completely

lower the blade unit and lock it in place using the pin

F (g. 1)

(RI and NTF305 version)

– This version is equipped with ne-adjustment:

adjust the height of the upper table using the knob N

(g. 1) and then lock the table in position by tightening

the knob S (g. 1).

(RP version)

- Adjust the height of the upper table as required by

the piece to be cut, and then lock in position using the

corresponding knobs S (g. 1) and T (g.9).

6.7.1 STARTING AND STOPPING THE BLADE

- Start the blade by pressing the tool lever A (g. 2)

and then press the black key B (g. 2) and wait until

the blade reaches its maximum rpm. - Make the cut

desired.

After the cut has been made, press the lever A (g. 2)

and then release it and wait until the blade has come

to a complete stop.

6.8 USING THE STROKE-END GUIDE FOR THE

UPPER TABLE (g. 9)

Proceed as follows: - Insert the guide G (g. 9) in the

upper table – Select the desired cutting width using the

graduated scales – Lock into the guide G into position

using the knob H.

6.9 CUTTING SMALL PIECES

Small pieces must be worked with the use of the correct

tools – On the lower table: Use the clamp to lock the

workpiece in place and the stroke-end rods to obtain the

size desired – On the upper table: Use the pusher (g.

20) provided to advance the workpiece.

Never put your hands on the workpiece to be cut.

Keep the pusher in a safe place nearby for use

whenever required.

6.10 CUTTING LARGE PIECES

Never remove the workpieces that have already been

cut or other parts of the workpieces to be cut while the

machine is working and the support is not in rest position.

Hello,
we need some parts of FELISATTI MT305S:
- M Movable lower blade protector
- K Machine lock knob 0°- 45°
- L Turntable lock knob
- S Upper table locking knob

Where I can find these parts?
I asked to some supplier but I didnt found them.
Thank you Submitted on 22-6-2023 at 16:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti NTF305 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti NTF305 Manual

Product: