Manual Felisatti NTF305 (page 12 of 52) (English, German, French, Italian, Spanish)

502512

Zoom out

Zoom in

1/52

6.11 IMPROPER USE

The functions and use of this tool are those exclusively

indicated in this manual. Never use the tool to cut thick

tree trunks or branches.

Any other use of the tool is explicitly forbidden.

-Never cut aluminium or steel on the upper table.

-Always use sharp blades appropriate to the type

of cuts to be made.

-Never use the machine without the protective

devices described.

-Never use the machine for food-processing

purposes.

-Use only the right types of blade (see Table, Point

6.1) for the material to be cut: wood, aluminium

sections, PVC pipe, etc.

The cutting of any other type of material not

specied in this manual is expressly prohibited.

The machine comes with a brush that conveys

all dust into the suction area in order to limit the

quantity of dust generated during cutting.

WARNING! Whenever wood is cut, connection to an

external vacuum unit must be used in order to lower

the risk of exposure to dust.

Always wear dust-proof face masks.

7 MAINTENANCE

WARNING - Always unplug the plug from the power

supply socket before performing.

maintenan

Note: operating noise can be decreased by

using the right blades and performing frequent

maintenance on the blade and mitre saw itself.

7.1 LUBRICATION

The mitre saw is delivered already completely

lubricated and does not require any further lubrication.

7.2 ROUTINE CLEANING

WARNING - Avoid touching the handgrip with hands

that are dirty with oil or grease, and immediately

clean the handgrip whenever this happens.

- Clean the machine carefully after use by spraying

with compressed dry air.

WARNING - An attachment that can be easily

connected to any Felisatti vacuum unit is provide to

improve work conditions.

7.3 CHECKING THE DRIVE BELT

These machines are equipped with drive belts.

The right tightness of these belts is essential to

good operation and must be checked regularly and

adjusted whenever necessary by proceeding as

follows:

- remove the casing over the belt A (g.16) and

loosen the 4 screws C (g. 17) that keep the motor

unit in place.

- adjust the tightness of the belt using the

corresponding dowel B (g. 17).

- tighten the 4 screws C (g. 17) in order to lock the

motor unit in place and reassemble the protective

casing ove the belt.

WARNING! The failure to perform this operation

regularly may result in damage to the belt and

incorrect machine operation.

7.4 DISPOSAL

At the end of the machine working life, or

when it can no longer be repaired, ensure

that it is disposed of according to the standard

regulations of the country in which it is being used,

and that the disposal operation is carried out by

specialised personnel following authorised guidelines.

In all circumstances:

- Do not abandon in the environment;

- Do not dispose of together with solid urban

waste products;

- Contact the special recycling centers

8 PART REPLACEMENT

WARNING! - Always unplug the plug from

the power supply socket before replacing

spare parts.

8.1 BLADE REPLACEMENT (g. 18)

Proceed as follows to replace the blade:

Raise the upper table to its highest permissible height

- Release the movable protective casing L (g. 1) by

using the button B and raise it completely - Using the

two Allen wrenches supplied (on the blade side and

on the motor side) unscrew the screw C clockwise -

Remove the locking ange D, remove the blade by

rst sliding it to the left and then sliding it downwards -

Mount the new blade after making sure that the teeth

face the direction indicated by the arrow and then lock

it in place by screwing the screw C counter-clockwise

tightly down - Lower the movable protective casing L

by returning button B to its original position and then

make sure that the blade is protected when the blade

unit is completely raised.

WARNING! - Use only the blades recommended by

the Manufacturer and in compliance with Standard

EN 847-1. Make sure that the speed marked on the

blade is greater than the tool rated speed.

WARNING! - NEVER USE STEEL BLADES FOR

HIGH SPEEDS.

8.2 REPLACING THE POWER SUPPLY CABLE

Make sure that the power supply cable is in good

condition; if worn, have it replaced by an authorised

Assistance center.

Hello,
we need some parts of FELISATTI MT305S:
- M Movable lower blade protector
- K Machine lock knob 0°- 45°
- L Turntable lock knob
- S Upper table locking knob

Where I can find these parts?
I asked to some supplier but I didnt found them.
Thank you Submitted on 22-6-2023 at 16:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti NTF305 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti NTF305 Manual

Product: