709781

Falmec Ellittica - wall Manual

27
Zoom out
Zoom in
Previous page
1/88
Next page
25
- Locate the desired height between the hood and hob (see sect. C).
- Remove the back (A) by removing the cover caps (T) and loosen the inside fastening screws
(V1).
- Mark the 4 drilling points F, according to the dimensional specifications shown in the figure,
or use the back as a drilling template.
Fig. W03-W04
- Fasten the back (A) to the wall using the 4, Ø8 mm expansion plugs and the screws (V2)
provided.
- Check the horizontal and vertical alignment of the back with a spirit level.
Fig. W05-W06
- For the exhaust version, (define the upper and lower output use) locate the optimal length
of the fumes exhaust pipe (F) and connect. To facilitate the operation, if the ceiling height
allows it, cover B can be temporarily removed by acting on fastening screws. Carry out elec-
trical connections only after disconnecting the power supply. For the filter version, make
sure the exhaust on cover B is free to allow the air purified by carbon filters to be exhausted.
- Attach the hood to the back using the 4 hooks (G) ensuring the hood is down by approx 10
mm, to check its tightness.
Fig. W07-W08
- Tighten, but not completely, the two upper fastening screws (V1).
- Lift the hood to the desired position and tighten the upper and lower fastening screws com-
pletely (V1).
- Power the hood in accordance with applicable regulations (see sect. D of this booklet).
HOOD INSTALLATION WITH GLASS (optional fig. W09-W10-W11-W12-W13)
- Remove the metal filter using handle (C). Disconnect the hood from the mains.
- Disconnect connector (S) of the spotlights cable.
- Remove the body (A) from the cone (B+D) loosening the 4 M4 milled metric screws (V3).
- Slightly loosen the 2 centring and anti-rotation metric screws (V4) in the lower flange of the
cone (B), and centre the glass slot with the metric screws.
- Fasten the body (A) to the cone (B) with the 4 M4 milled metric screws (V3).
- Refit the metal filter using handle (M). Supply power in accordance with applicable regula-
tions (see sec. D of this booklet).
N2
INSTALLATION INSTRUCTIONS FOR POLAR HOOD WITHOUT GLASS
PREDISPOSITION
ISLAND HOOD
Fig. 1-2
- Remove the fastening screws between the extension and trellis (only for transport).
- Fasten the top trellis (C) to the ceiling using the 6, 8 ø Fischer anchors and the screws
provided(V1).
Fig. 3-4
- Locate the desired height between the hood and the hob (see sect. C).
- Fasten the lower three-piece unit (chimney + extension +trellis, B+D+G) to the upper trellis
(C) using the 6 self-tapping screws (V2), making the lower trellis slide (G) inside the upper
trellis (C).
- For the exhaust version, locate the optimal height of the fumes exhaust pipe, and connect.
For the filter version, the upper extension slots must remain free to allow the air purified by
carbon filters to be exhausted.
- Make electrical connections only after having disconnected the electric power supply.
Fig. 5
- Slide the extension (D) upwards under the upper flange of the trellis. Next, turn clockwise
English
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falmec Ellittica - wall at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Ellittica - wall in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish, All languages as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info