709781
26
Zoom out
Zoom in
Previous page
1/88
Next page
24
WARRANTY
M
The new equipment is covered by warranty. The warranty conditions are provided by the dis-
tributor.
The manufacturer is not liable for any inaccuracies in this booklet resulting from printing or
transcription errors. The manufacturer reserves the right to modify its products as it consid-
ers necessary or in the interests of the user, without compromising their essential safety and
operating characteristics.
N
MOUNTING INSTRUCTIONS FOR POLAR ISOLA
HOOD
WARNING: Failure to install the screws or fixing device in accordance with these instructions
may result in electrical hazards.
N1
INSTALLATION INSTRUCTIONS FOR POLAR HOODS WITH GLASS
PREDISPOSITION
ISLAND HOOD
Fig. 1-2
- Remove the fastening screws between the extension and trellis (only for transport).
- Fasten the top trellis (C) to the ceiling using the 6 Fischer anchors, ø 8, and the screws pro-
vided (V1).
Fig. 3-4
- Locate the desired height between the hood and hob (see sect. C).
- Fasten the lower three-piece unit (chimney + extension + trellis, B+D+G) to the upper trellis
(C) using the 6 self-tapping screws (V2), making the lower trellis slide (G) inside the upper
trellis (C).
- For the exhaust version, locate the optimal height of the fumes exhaust pipe, and connect.
For the filter version, the upper extension slots must remain free to allow the air purified by
the carbon filters to be exhausted.
- Make electrical connections only after disconnecting the power supply.
Fig. 5
- Slide the extension (D) upwards under the top flange of the trellis. Next, turn it clockwise
until it is hooked to the flange, and then secure it permanently with the M3 metric screw
provided.
- Power the hood in accordance with applicable regulations (see sect. D of this booklet).
HOOD INSTALLATION WITH GLASS (OPTIONAL) (fig. O6-07-08-09-10)
- Remove the metal filter using handle (M). Disconnect the hood from the mains.
- Disconnect the connector (S) of the spotlights cable.
- Remove the body (A) from the chimney and extension (B+D) unit, loosening the 4 M4 milled
metric screws (V3).
- Slightly loosen the centring and anti-rotation metric screws (V4) in the lower flange of the
cone (B), then centre the glass slots with the metric screws.
- Fasten the body (A) to the chimney and extension unit (B+D) with the 4 M4 milled metric
screws (V3) provided.
- Reconnect connector (S).
- Refit the metal filter using the handle (M). Supply power in accordance with applicable
regulations (see sec. D of this booklet).
WALL HOOD
Fig. W01-W02
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falmec Ellittica - wall at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Ellittica - wall in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish, All languages as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info