71518
53
Zoom out
Zoom in
Previous page
1/60
Next page
53
WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Taking care not to damage the burner electrodes, carefully lift the
hotplate, from underneath disconnect the earth lead at the right
hand rear from the rear cross member and withdraw the hotplate.
Reassemble in reverse order ensuring that the leads are
reconnected. Take care not to damage the ignition electrodes of
the burners.
It is important that the rear earthing leads are replaced when the
xing screws are refi tted as they from part of the cooker earthing.
Check for correct burner operation.
3. To Remove Side Panels
Disconnect from electricity supply.
Remove the Control Panel - see 1. Pull the cooker forward.
Remove the 4 retaining screws for each panel (1 at the front base,
1 on the top and 2 at the rear).
Reassemble in reverse order.
4. To Remove light Switch
Disconnect from electricity supply.
Remove the Control Panel - see 1.
NB. The old switch may be destroyed during removal. Remove the
old switch from its bezel by griping the switch body behind the
control panel and twisting sharply. The switch bezel can then be
removed by folding back its locking wings and pushing forward.
Fit the new bezel to the control panel by fi rst lining up the raised
key on its body with the cutout in the control panel and pushing
it in from the front. Assemble the new switch to the bezel by
lining up the key sections and pushing home. Fit the new button
by pushing in from the front.
Replace Control Panel in reverse order and test for correct
operation.
5 To Change an Ignition Switch
Change the gas tap as detailed in Section 9.
6. To Remove Clock
Disconnect from electricity supply.
Remove the Control Panel (See 1). Pull off the timer control
button(s).
Remove the timer/mounting bracket assembly from the control
panel by removing the fi xing screws.
Remove the timer from its mounting bracket by depressing the
plastic lugs on the timer case, at the same time pulling the unit
forward.
Servicing
BEFORE SERVICING ANY GAS CARRYING COMPONENTS. TURN
OFF THE GAS SUPPLY
Check the appliance is gas sound after completion of service.
When checking for gas leaks do not use washing up liquid - this
can corrode. Use a product specifi cally manufactured for leak
detection.
Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before commencing
servicing, particularly before removing any of the following:
- control panel, side panels, hotplate tray or any electrical
components or covers.
Before electrical re-connection, check that the appliance is
electrically safe.
Note - References to left hand and right hand oven apply as
viewed from the front.
1 To Remove the Control Panel
Disconnect from electricity supply.
Pull off all the control knobs.
Open the grill and right hand oven doors and remove the 4 fi xing
screws underneath the control panel.
The control panel should drop down slightly. It is held at the top
by two holes in the top edge one at each end that locate on tags
on the inner panel.
Clear the holes from the inner panel and pull the control panel
forward.
Disconnect the wiring from the rear.
Reassemble in reverse order. When replacing leads refer to the
wiring diagram. Check operation of timer.
2. To Remove Hotplate
Disconnect from electricity supply.
Caution
The ceramic hob material is much more sensitive to scratches
on the underside than the top.
Take care not to touch or scratch the underside of the ceramic
as this will weaken the material and cause the top to shatter.
Remove the pan supports and burner heads. Remove the screws
holding the hotplate burners to the hotplate.
Remove the 6 screws and 2 studs holding the hotplate tray to the
cooker.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon Excel 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon Excel 110 in the language / languages: English, German as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falcon Excel 110

Falcon Excel 110 User Manual - Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info