71518
54
Zoom out
Zoom in
Previous page
1/60
Next page
54
WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Reassemble in reverse order. When replacing leads refer to the
wiring diagram. Check operation of timer.
7. To Remove an oven Thermostat
Disconnect from the electricity supply.
Remove control panel and hotplate (see 1 & 2). Open oven door.
Remove oven furniture and slide out oven roof liner if fi tted. Pull
cooker forward to gain access to the cover box at the rear of the
cooker. Remove the screws securing the cover and lift clear. The
oven thermostat capillary is clamped to the oven back sheet with
an earthing plate. Remove the screws and plate.
thermostat capillary
earthing plate
Left Hand Main oven
Remove the two screws holding the thermostat phial to the oven
fan cover at the rear of the oven.
Right hand Main oven and Slow Cook oven
Remove thermostat phial cover (2 screws). Unclip the thermostat
phial from the clips on the oven back.
Slow cook oven thermostat phial cover.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding thermostat to
mounting panel. Fit new thermostat and reassemble in reverse
order. Ensure that the phial is clipped to the oven back with the
phial centrally positioned between the clips.
Remember to refi t the earthing plate.
Check operation of thermostat.
8. To Change the Grill or Ceramic hob Controller
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2). Disconnect
wiring from controller. Remove 2 screws holding controller to
mounting panel. Fit new controller and reassemble in reverse
order. Check for correct operation.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS TURN OFF
GAS SUPPLY.
9. To Change a Hotplate Tap
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Unplug the FSD lead from the rear of the tap. Undo compression
tting at the rear of the tap. Remove the fi xings that secure the
tap to the gas rail. Disconnect the ignition switch wiring.
Remove the tap. Remove and discard the gasket seal. Fit new
gasket seal to replacement tap. Re-assemble in reverse order.
Check the appliance is gas sound. Check hotplate ignition.
10. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new injector.
Reassemble in reverse order. Check appliance is gas sound.
11. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the screw
holding the electrode. Pull electrode vertically up suffi ciently
to grip the lead between thumb and forefi nger. Pull off the
electrode, but keep hold of the lead. Fit new electrode to the
lead. Fix electrode in burner with screw. Replace burner cap.
Check the burner ignition. Replace pan supports.
12 To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
The burners except the right hand wok burner are mounted on
support struts. For these burners, disconnect the burner feed
pipes at the burner. Remove the screws at the front and rear
holding the support stru ts. Lift the strut and burners clear. The
burners are fi xed to the support struts with 2 screws. Remove the
appropriate burner and fi t the new one. Reassemble in reverse
order. Check burner operation is satisfactory.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the new
one and reassemble in reverse order. Check burner operation is
satisfactory.
13. To Remove an Oven Door
Open the oven door. Loosen the two top hinge screws.
Support the weight of the door and remove the screw nearest
the hinge pin. Swing the hinge up and away from the hinge pin
on the door.
Lift the door away from the bottom hinge.
Re-assemble in reverse order. When replacing the door ensure
that the nylon hinge bush is in position between the hinge pin
and the hinge bracket at the both the bottom and top.
14. To Change Oven Door Outer Panel
Move the cooker forward
to gain access to the sides.
Open the oven door
slightly and remove the
front panel fi xing screws
from the door sides (two
each side).
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2 retaining nuts.
Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon Excel 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon Excel 110 in the language / languages: English, German as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falcon Excel 110

Falcon Excel 110 User Manual - Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info