71518

Falcon Excel 110 Manual

51
Zoom out
Zoom in
Previous page
1/60
Next page
51
English
Levelling
You are recommended to use a spirit level on a shelf in one of the
ovens to check for level.
Place the cooker in its intended position taking care not to twist
it within the gap between the kitchen units as damage may occur
to the cooker or the units.
The rollers can be adjusted to level the cooker. To adjust the
height of the rear of the cooker use the levelling tool supplied to
turn the adjusting nuts at the front base of the cooker.
Adjust the height of the front roller to level the cooker. Turn
clockwise to raise the cooker and anticlockwise to lower.
When you are satisfi ed with the height and level raise the front
of the cooker by one turn of the front roller adjuster. Screw down
the front feet to meet the fl oor. Screw the front roller adjuster
anticlockwise to raise the front roller so that the front of the
cooker is supported on the feet, not the front roller, to prevent
accidental movement of the cooker.
Fitting the splash back (optional)
Remove the two fi xing screws (3mm hexagonal socket head) and
nuts that pass through the top of the rear fl ue grille. Hold the
splash back in position. From the rear refi t the 2 fi xing screws and
nuts.
Gas Connection
Restraining device
A restraining device should be fi tted when the cooker is
connected to a fl exible gas supply. Any restraining device should
be secured to the fabric of the building and should be able to be
released so that the cooker can be pulled out for cleaning and
maintenance.
Flexible Gas Hose
A gas shut off valve must be fi tted between the gas supply and
the connection hose. The fl exible hose (not supplied with the
cooker) must be in accordance with the relevant standards. If in
doubt contact, your supplier.
The gap between the cooker rear cover boxes and the rear wall
when the cooker is pushed back is only 50mm
The inlet connection on the cooker is ISO 7-1 internal. If you
require a ISO 228-1 connection fi nd the ISO 7-1 to ISO 228-1
connector in the conversion kit. Apply a suitable thread sealing
compound to the ISO 7-1 end.
Screw the connector into the cooker inlet until it is fi nger tight.
Using two suitable tools, one on the inlet on the cooker to make
sure it is held steady and one on the connector, tighten the
connector into the inlet on the cooker.Minimum torque 15Nm.
Maximum torque 20NmConnect the hose to the connector.
The hose should be fi tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in a
‘U’ shape. The gap between the cooker rear cover boxes and the
rear wall when the cooker is pushed back is only 50mm.
view from the rear
A appliance gas inlet
B position for gas supply connector, alternatively connect from the
side.
C electrical terminal cover
Because the height of the cooker can be adjusted and each
connection is diff erent it is diffi cult to give precise dimensions.
Ideally the house supply connection should be in the shaded
area shown in the fi gure showing the back of the cooker (‘A’ in the
fi gure). Alternatively connect from the side.
After completing the gas connection, check the cooker is gas
sound with a pressure test. When checking for gas leaks do
not use washing up liquid - this can corrode. Use a product
specifi cally manufactured for leak detection.
CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.
Pressure testing
The gas pressure can be measured at the injector of one of the
centre hotplate burners. Remove the pan support, burner head
and cap. The injector is now accessible. Turn and light one of the
hotplate burners.
See Technical data section at the back of this book for test
pressures.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Electrical Connection
This appliance must be installed by a qual i fi ed electrician to
comply with the relevant In sti tute of Electrical Engineers (I.E.E.)
regulations and also the local elec tric i ty supply company
re quire ments.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
The cooker must be connected to the cor rect electrical supply
as stated on the voltage la bel on the cooker, through a suitable
cooker control unit incorporating a double pole switch having a
contact separation of at least 3mm in all poles. This cooker must
not be connected to an ordinary domestic power point.
The total electrical load of this appliance is 11.7kW at 230VAC
It must be connected to an electrical supply, either single phase
or multi phase that can sustain a maximum current fl ow of at
least 51 amps. (Unless local regulations allow this loading to be
reduced by applying diversity factors).
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon Excel 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon Excel 110 in the language / languages: English, German as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falcon Excel 110

Falcon Excel 110 User Manual - Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info