Manual Falcon 900 Deluxe (page 26 of 32) (English)

76488

Zoom out

Zoom in

1/32

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Servicing

When servicing or replacing gas carrying components,

disconnect from the gas supply before commencing

operation.

Check the appliance is gas sound after completion of

service. When checking for gas leaks do not use

washing up liquid - this can corrode. Use a product

specifically manufactured for leak detection.

CAUTION: DO NOT USE A FLAME TO CHECK

FOR GAS LEAKS.

Do not use re-conditioned or unauthorised gas

controls.

Disconnect from the electricity supply before

commencing servicing, particularly before removing

any of the following: - control panel, side panels,

hotplate tray or any electrical components or covers.

Before electrical re-connection, check that the

appliance is electrically safe.

Note - References to LH and RH oven apply as viewed

from the front.

BEFORE SERVICING ANY GAS CARRYING

COMPONENTS. TURN OFF THE GAS SUPPLY.

1 To Remove the Hotplate

Disconnect the appliance from the electricity supply.

Pull the unit forward to gain access.

a) Remove the pan supports/hotplate accessories and

burner caps.

b) Remove the brass venturi in the centre of each

hotplate burner bezel.

c) Remove the bezel from the hotplate and disconnect

the spark ignition lead from the spark electrode.

d) Lift the hotplate clear of the appliance.

e) Replace in reverse order.

2 To Remove the Control Panel

Disconnect the appliance from the electricity supply.

a) Remove the pan supports/hotplate accessories and

burner caps.

b) Slacken the brass venturi at the centre of each

burner.

c) Remove the control knobs from all taps.

d) Open the grill and RH oven doors. Remove 3 fixings

on the top front and 3 fixings on the control panel

underside.

e) Pull the control panel forward. Remove the

connections from the rear of the three neons.

Disconnect the earth lead and lift the panel clear of

the unit.

f) Replace all parts in reverse order.

g) When replacing any electrical connections refer to

the wiring diagram.

3 To Remove an Outer Side Panel

Disconnect the appliance from the electricity supply.

a) Remove the control panel as detailed in Section 2

b) Remove the retaining screw on the upper front edge

and the two fixings on the rear or the side panel.

Undo the lower retaining screw situated below the

edge at the panel front corner.

c) Remove the panel by pulling it away from the unit.

Should difficulty be encountered, it may be

necessary to slacken the two closest burners and

both brass venturi as detailed in Section 1.

d) Replace parts in reverse order. Ensure that both

venturis are fully tightened.

4 To Remove an Oven or Grill Neon

Disconnect the appliance from the electricity supply.

a) Remove the control panel as detailed in Section 2

b) Remove the relevant neon connection and undo the

nut which secures the neon to the control panel.

c) Replace parts in reverse order. Ensure the

replacement neon functions correctly.

5 To Remove a Thermostat

Disconnect the appliance from the electricity supply.

a) Remove the hotplate as detailed in Section 1.

b) Remove the control panel as detailed in Section 2

c) Open the appropriate oven door and remove the

oven shelves.

d) Pull the unit forward to gain access to the cover box.

Undo the cover screws and lift clear.

RH oven

Remove the two fixings that secure the thermostat

phial cover. Unclip the thermostat phial from the clips

in the oven back panel.

LH oven

Remove the two screws holding the thermostat phial

to the oven fan cover at the rear of the oven. Pull the

unit forward to access the rear of the cooker.

Remove the both cover boxes by removing the fixing

screws and lifting clear. Feed the thermostat capillary

clear of the oven.

d) Disconnect the wires from the thermostat and undo

the two fixings which secure the control to the

mounting plate.

e) Fit the replacement and re-assemble in reverse

order. Ensure that the phial is clipped to the oven

rear, positioned centrally between the clips. Check

that the thermostat functions correctly.

6 To Replace a Grill Controller

Disconnect the appliance from the electricity supply.

a) Remove the hotplate as detailed in Section 1.

b) Remove the control panel as detailed in Section 2.

c) Disconnect the controller wiring. Undo the fixings that

secure the device to the mounting plate.

d) Fit the replacement and re-assemble parts in reverse

order. Check that the replacement functions

correctly.

7 To Remove an Oven Cut-Off Thermostat

Disconnect the appliance from the electricity supply.

a) Pull the unit forward to gain access to the cover box.

Undo the cover screws and lift clear.

b) The control is located on the earth plate beside the

oven element connections.

c) Disconnect the thermostat wiring. Undo the fixings

that secure the thermostat to the earth plate and

remove.

d) Fit replacement control and re-assemble parts in

reverse order.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 900 Deluxe in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Falcon 900 Deluxe Manual

Product: