76488
25
Zoom out
Zoom in
Previous page
1/32
Next page
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
25
Conversion to Propane
Servicing - warning
This conversion must be performed by a competent
person. After conversion the installation must comply
with the relevant regulations and also the local
electricity supply company requirements. Read the
instructions before converting this appliance.
Failure to convert the appliance correctly could
invalidate any warranty or liability claims and lead to
prosecution.
This instruction must be used in conjunction with the
rest of the appliance instruction, in particular for
information on Standards, cooker positioning,
connection hose suitability etc.
When servicing or replacing gas-carrying
components disconnect from gas before
commencing operation and check appliance is gas
sound after completion.
Do not use re-conditioned or unauthorised gas
controls.
Conversion
Disconnect from electricity and gas before servicing.
Check appliance is safe when you have finished.
This appliance is CAT II 2H3P. It is supplied set for
G20 natural gas at 20millibar
A conversion kit for Propane (G31 37mbar) is
supplied with the cooker.
Injectors
Remove pan supports burner caps and heads. Undo
the large brass nuts and remove the brass venturis.
Lift up the front of the hotplate top and disconnect the
ignition leads from the electrodes. Remove the
hotplate top.
Remove old jets. Fit the new jets (see Technical
Data section at the back of the book for correct jets).
Tap adjustment
Pull off all the control knobs.
Open the oven door & grill door and remove the
fixing screws underneath the control panel.
Remove the 3 fixing screws at the top of the control
panel.
Pull the control panel forward. Rest it on the open
grill door and the open right hand oven door.
To convert the control taps
Remove the bypass screws and fit the correct
replacements.
See table at the back of this book for correct size.
Refit the control panel.
Reassemble
Reassemble in reverse order.
Fit the larger internal diameter venturis to all the
burners. Tighten the large brass nuts.
Reassemble burner tops, making sure they are
reassembled in the correct way on the burner bodies.
Stick on label
Stick the appropriate label on to the data badge to
indicate the gas the appliance is now set for.
Pressure Testing
Connect the appliance to the gas supply. Check the
appliance is gas sound.
See Technical data section at the back of this book
for test pressures.
The gas pressure can be measured at the pressure
test point on the gas connection block. Turn and light
one of the hotplate burners.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon 900 Deluxe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 900 Deluxe in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info