34555
41
Zoom out
Zoom in
Previous page
1/46
Next page
THE INDUCTION HOB
Technical training
- 41 -
CU3-INDUCTION-003UK-10/05
DIAGNOSTIC
14.3. - Tests and measurements on IX3, IX3WR, IX4000 and IX6
Where the action on the board is not desired, the diagnostic will be limited to the defective element.
Any action on the circuit shall be carried out after eliminating the causes that may be due to saucepans
or to a bad installation.
To avoid damaging the electronic components, never touch the circuit with your fingers.
14.3.1. - The test keyboards
During a diagnostic, it is necessary to know whether it is the
control keyboard or the power board, which is defective.
However, you must not omit the filter board, which includes two
fuse pads and the power supply relay. Generations IX3 on the
one hand and IX3WR, IX4000, IX6 on the other hand do not
use the same encoding process. It is therefore advisable to be
provided with two different test keyboards.
IX3 keyboard: 79X5460
IX3WR, IX4000 and IX6 keyboards: 79X9920
This keyboard will enable all the keyboard of each range to be replaced.
In event of degradation with use, baseplates can be replaced:
6-point baseplate (IX3) : 79X5461
8-point baseplate (IX3WR, IX4000, IX6) : 79x9921
14.3.2. - The IX3 and IX3WR filter board
These two generations have a different control but use the same filter board.
This board includes:
A direct output for the control power supply
A relay for the power supply
Two fuse pads
The fan power supply (via the relay).
In event of problem with power supply,
it is advised to check:
Whether 'fuse' pads are out of order
Whether the power relay is controlled (12VDC)
Whether the relay delivers 230VAC to the board.
Whether the relay delivers 230VAC to the fan
Note: Fuse pads are also present on the IX6
and IX4000 boards.
CAUTION : It is necessary to reinstall the glass-ceramic top to conduct the tests.
N L L N
Power relay
285 relay
coil
Outputs
after relay
Ground
screw
Fuse
pads
Fan
connector
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fagor Brandt CU3 induction 003UK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fagor Brandt CU3 induction 003UK in the language / languages: English as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info