752956
7
Zoom out
Zoom in
Previous page
1/16
Next page
Version 05/10- Page 7
INSTALL THE RANGEHOOD
1. Remove the grease filters from the unit and set aside. The
grease filters are removed by pressing the handle in front of the
filter (FIGURE 9). When replacing, make sure that the filters are
properly positioned with the handles in front and visible.
FIGURE 11
FIGURE 12
FIGURE 9
2. Determine and make all necessary cuts in the wall for the vent
system. Install the vent system before installing the range
hood. See the “Venting Requirements” section.
3. Determine and mark the location where the hole will be drilled
for the power supply cable to be run through the wall. See
FIGURE 10 for locating the power supply. Take the distance
from the cooktop (F) and hood install height (D), and add 3"
(A). Mark and drill a hole (B) = 1 1/4" diameter on the wall on
the left side of the hood (C) 7 1/4" for 30" hoods, and 8 1/4" for
36" hoods from the center line (E).
FIGURE 10
Vented Installations
1. Install damper on top of the exhaust opening. Check that the
damper opens freely. Install the ductwork and seal all
connections with duct tape before mounting the hood.
2. Go to “Mount the Range Hood” in this section.
Non-vented (ductless) Installations
NOTE: Ductless Kit Part #DUCTCLAS is required.
1. Install the non-vented (ductless) diverter supplied with the
recirculating kit. See (FIGURE 11)
2. Fit the diverter over the vent exhaust outlet and push
down to seat on outlet. Check that the diverter exhaust
outlets are parallel with the vent motor sides so that they will
align with the vent cover openings in the lower chimney.
3. Attach the CHARCOAL FILTERS to both sides of the blower
(as indicated in FIGURE 12).
MOUNT THE RANGE HOOD
1. Using 2 or more people, lift the range hood and place
the mounting hood brackets over the mounting screws.
FIGURE 13
2. Run the home power supply cable (black, white and
green wires) through the strain relief in the back of the
range hood and into the terminal box.
3. Push the range hood into its mounted position. The ½"
strain relief should fit into the 1¼" diameter hole when
the rangehood is seated into position.
4. Securely tighten the mounting screws.
FIGURE 13
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Classica at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Classica in the language / languages: English, French as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info