560694
17
Zoom out
Zoom in
Previous page
1/40
Next page
15
C850 532015 Rev. A
FSW OP
FSW CL
RCL
FCCFCO
FSW CL
EF
ROP
INVERTER
L
LIMIT SWITCH UNIT
ENGLISH
To connect the
photocells and
safety devices,
refer to paragraph
11.4.2.
Fig. 28
11.4.1 TERMINAL BOARD J1 - ACCESSORIES (FIG. 28)
J6=FCC - FCO - Manoeuvre stop command.
J5=RCL - Start of closing deceleration.
J3=ROP - Start of opening deceleration.
LOOP 1 - LOOP 1 magnetic loop (OPEN - terminals 1-2): for OPENING.
LOOP 2 - LOOP 2 magnetic loop (SAFETY/CLOSE - terminals 3-4): for SAFETY/CLOSING.
EF - Electrical stopping brake for motor locking.
OPEN - “Open” command (N.O. - terminal 5): means any pulse generator (e.g.: button) which, by closing a contact, commands
opening and/or closing of the gate.
CLOSE - “Close” command (N.O. - terminal 6): means any pulse generator (e.g.: button) which, by closing a contact, commands
closing of the gate.
FSW CL - Safety contact when closing (N.C. - terminal 7): he purpose of the closing safety devices when closing is to protect the
area affected by the movement of the gate during the closing phase, reversing the motion. They never trip during the opening cycle.
The CLOSING SAFETY DEVICES, if tripped when the automated system is open, will prevent the closing movement.
If CLOSING safety devices are not connected, jumper terminals FSW CL and GND (Fig. 32).
NOTE: If this connection is made, it will not be possible to use the FAILSAFE control.
STOP - STOP contact (N.C. - terminal 8): means any device (e.g.: button) which, by opening a contact, can stop movement of
the automated system.
If STOP devices are not connected, jumper terminals STOP and GND (Fig. 32).
FSW OP - Safety contact when closing (N.C. - terminal 9): the purpose of the opening safety devices when opening is to protect
the area affected by the movement of the gate during the opening phase, reversing its motion. They never trip during the closing
cycle. The OPENING SAFETY DEVICES, if tripped when the automated system is closed, will prevent the opening movement.
If OPENING safety devices are not connected, jumper terminals FSW OP and GND (Fig. 32).
GND (terminals 10-11-19) - Accessories power supply negative
24 VDC (terminals 12-13) - Accessories power supply positive
The max. load of the accessories is 500 mA. To calculate absorption, refer to the instructions included with
the individual accessories.
OUT 1 - DECELERATION COMMAND (terminal 14): signal telling the inverter that deceleration has begun.
OUT 2 - CLOSE COMMAND (terminal 15): signal telling the inverter that the gate is closing.
OUT 3 - OPEN COMMAND (terminal 16): signal telling the inverter that the gate is opening.
To avoid compromising correct system operation, do not exceed the power indicated in fig. 28.
OUT 4 - Output 4 open-collector +24 VDC (terminal 18): the output can be set in one of the functions described in Advanced
Programming Level (par. 11.5.2.). The default value for ALL PRE-SETTINGS is BUS COMMUNICATION.
Maximum load: 24 VDC with 100 mA.
60 W max
230 V~
230 V
~
50/60 Hz
11.4 ELECTRICAL CONNECTIONS
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FAAC C850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FAAC C850 in the language / languages: English as an attachment in your email.

The manual is 13,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info