560694
19
Zoom out
Zoom in
Previous page
1/40
Next page
17
C850 532015 Rev. A
ENGLISH
After positioning the BUS-technology photocells, proceed with
selecting the address for each pair using various combinations
of the DIP-SWITCHES located on each photocell.
Set the SAME chosen DIP-SWITCH ADDRESS on both
the transmitter and receiver of the same pair.
Ensure that two or more pairs of photocells do not
have the same address.
If no BUS accessories are used, leave terminals 18
and 19 free.
The following table describes how to set the dip-switches located
inside the transmitter and receiver of the BUS photocells.
Table - Addressing BUS photocell PAIRS
Dip1 Dip2 Dip3 Dip4 Ref. Type
ON OFF OFF OFF
B-C
OPENING
OFF OFF OFF ON
OFF OFF ON OFF
OFF OFF ON ON
OFF ON ON OFF
OFF ON ON ON
ON OFF OFF OFF
D
CLOSING
OFF OFF OFF ON
ON OFF ON OFF
ON OFF ON ON
ON ON OFF OFF
ON ON OFF ON
ON ON ON OFF
OFF ON OFF OFF
A
OPENING and
CLOSING
OFF ON OFF ON
ON ON ON ON /
OPEN
PULSE
TX DIP-
SWITCH
RX DIP-
SWITCH
SAME
ADDRESS
To allow operation of the installed BUS
accessories, store them on the board, as
described in paragraph 11.5.3.
11.4.4 TERMINAL BOARD J2, FLASHING LAMP
(FIG.28)
LAMP (LAMP-COM): Flashing lamp output.
11.4.5 TERMINAL BOARD J9 - POWER SUPPLY (FIG. 34)
PE: Earth connection
N: 230 V~ or 115 V~ Power supply (Neutral)
L: 230 V~ or 115 V~ Power supply (Line)
For correct operation, you must connect the
board to the system’s earth conductor. Ensure
that a suitable differential magnetothermic
switch has been installed upstream.
11.4.6 CONNECTORS J3, J5 - RAPID CONNECTION
OPENING AND CLOSING LIMIT SWITCHES (FIG. 28)
Rapid connector for connecting the opening (J3) and closing (J5)
limit switches.
11.4.7 FREQUENCY SELECTOR DS1 (FIG. 27)
DIP-SWITCH used to set the HIGH or LOW work frequency of
the vehicle detection loops. See section 11.5.5.
11.4.8 CONNECTOR J4 - MINIDEC, DECODER
AND RP CONNECTOR
Used for the rapid connection of the Minidec, Decoder and RP /
RP2 Receivers.
If a 2-channel receiver is used, like the RP2, it will be possible to
directly command automated system OPEN and CLOSE from a
2-channel radio control.
If a 1-channel receiver is used, like the RP, it will only be possible
to command OPEN.
Connect the accessory with the components side facing inside
the board.
Boards should be connected or disconnected
ONLY after having cut off electrical power.
Fig. 35
Example of radio accessory connection
Fig. 34
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FAAC C850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FAAC C850 in the language / languages: English as an attachment in your email.

The manual is 13,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info