560694
16
Zoom out
Zoom in
Previous page
1/40
Next page
14
C850 532015 Rev. A
ENGLISH
11 E850 ELECTRONIC CONTROL UNIT
11.1 WARNINGS
Important: Before carrying out any work on the control unit (connections, maintenance) always cut off the
electrical power.
Always install a differential magnetothermic switch with a suitable activation threshold upstream from the system.
Connect the earthing cable to the corresponding terminal on connector J9 of the equipment (see fig.28).
Always separate the power cables from the control and safety cables (button, receiver, photocells, etc.). To avoid any electrical
disturbance, use separate sheaths or a shielded cable (with the shield connected to the earth).
11.2 E850 TECHNICAL SPECIFICATIONS
Power voltage
230 V
~
(+6% -10%) - 50/60 Hz
Absorbed power
7 W
Maximum motor
load
1800 W
Accessories
power supply
24 Vdc
Max accessories
current
500 mA
Operating ambient
temperature
from -20°C to +55°C
Protection
F1 = F 5A - 250V F2 = T 0,8A - 250V
or
F1 = F 10A - 120V F2 = T 0,8A - 120V
Operating time
Programmable (from 0 to 4 min)
Pause time
Programmable (from 0 to 4 min)
Programming
3 programming levels for greater
exibility of use
Rapid connector
5-pin board connector for Minidec,
Decoder, RP/RP2 Receiver
Characteristics
Multi-function display, BUS technology and
INTEGRATED METAL MASS DETECTOR
11.3 E850 LAYOUT AND COMPONENT DESCRIPTION
11.3.1 E850 LAYOUT
11.3.2 E850 COMPONENT DESCRIPTION
DL
SIGNALLING AND PROGRAMMING DISPLAY
LED
INPUT STATUS CONTROL LEDs
J1
LOW-VOLTAGE TERMINAL BOARD
J2
MOTOR, FLASHING LAMP AND FAN CONNECTION
TERMINAL BOARD
J3
ROP OPENING DECELERATION CONNECTOR
J4
DECODER / MINIDEC / RP RECEIVER CONNECTOR
J5
RCL CLOSING DECELERATION CONNECTOR
J6
STOP CONNECTOR
J9
230 VAC POWER SUPPLY TERMINAL BOARD
DS1
LOOP 1 and LOOP 2 FREQUENCY SELECTOR
F1
MOTOR FUSES AND TRANSFORMER PRIMARY (F 5A)
F2
LOW-VOLTAGE AND ACCESSORIES FUSE (T 800mA)
F
“F” PROGRAMMING BUTTON
+
“+” PROGRAMMING BUTTON
-
“-” PROGRAMMING BUTTON
TF1
TRANSFORMER
Fig. 26
Fig. 27
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FAAC C850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FAAC C850 in the language / languages: English as an attachment in your email.

The manual is 13,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info