814231
15
Zoom out
Zoom in
Previous page
1/28
Next page
INSTALLATION INSTRUCTIONS
Examples of hydraulic installation: Top, side, rear.
Use of ½ inch pipes is recommended.
STORAGE WATER HEATER MODE INSTALLATION
Remove the 2 covers for the installation of the system pipes and the fume
duct. The fume duct must be certified according to EN1856-2. The use of
flexible tubing is recommended to connect the appliance to the hydraulic
system as, in the case of routine or non-routine maintenance, this will make
it easier to move.
Hot and cold water pipes are ½ inch. The hot water pipe is indicated using a
sun and the cold water pipe is indicated with snowflake symbol.
IMPORTANT: A circuit board and safety thermostat installed
in the item may reduce the risk of malfunction. Installation of
a safety hydraulic circuit according to EN 1487 is also
mandatory. It is a good practice to connect the drain of the
unit to a pipe with the required specifications.
Installation of an expansion tank is recommended to prevent
harmful water hammer or accidental overpressures from
occurring. A mixing valve to prevent water at
overtemperatures in the circuit must also be installed.
The manufacturer assume no liability for damage to property
or injury to persons following failure to install the safety
devices correctly.
THERMO-STOVE MODE INSTALLATION
Remove the 2 covers for the installation of the system pipes and the fume
duct. The fume duct must be certified according to EN1856-2. The use of
flexible tubing is recommended to connect the appliance to the hydraulic
system as, in the case of routine or non-routine maintenance, this will make
it easier to move.
Delivery and return pipes are ½ inch. The delivery is indicated with a sun and
the return is indicated with the snowflake symbol.
Install the electronic pump and expansion tank according to the system and
as described above. The safety valve must be at a maximum of 4 BAR.
It is also recommended to install a dirt separator as the electronic pump could
capture the dirt of the system and become jammed. It is RECOMMENDED
that an anti-condensation valve and a pressure gauge to read pressure are
installed. Remember to purge the hydraulic system before switching on the
appliance.
The system pressure must range from 0.5 to 2.5 bar. The recommended
pressure is 1.5 bar.
The manufacturer assume no liability for damage to property
or injury to persons following failure to install the safety
devices correctly.
14
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor TEK 80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor TEK 80 in the language / languages: English as an attachment in your email.

The manual is 2.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eva Calor TEK 80

Eva Calor TEK 80 User Manual - German - 28 pages

Eva Calor TEK 80 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info