Manual Eurom Flow 400 (page 11 of 28) (English, German, Dutch, French)

591568

Zoom out

Zoom in

1/28

Hose connection

Screw the curved fitting (supplied) to the pump, with the opening upwards, as in the

above photo. Now connect the hose connector to the fitting.

The hose connector narrows from 25 to 38 mm (or 1” to 1½”). If you are exclusively

using a 32 mm hose, you can remove the remaining piece of the fitting with a sharp knife

or saw. Attach the hose to the appropriate part of the connector with a hose clamp. The

best results of pumping efficiency are achieved with hose, as thick as possible.

Attaching the float switch

The pump is equipped with an adjustable float switch. You adjust the points at which the

pump switches itself on and off by shortening or lengthening the float cable using the

attachment on the handle.

You must check the following before using the pump for the first time:

 The float switch must be set so that the pump can reach the points at which it must

switch itself on and off easily and without any force. In order to check this, you must

place the pump in a container filled with water. Manually lift the float switch gently

and then allow it to descend. You will feel when the pump switches on and off and

can modify these points, if necessary, by shortening or lengthening the float cable via

the catch.

 Do not make the distance between the float and the cable catch on the handle too

short; the float switch needs a little space in order to run smoothly.

 When setting the float switch, ensure that it does not touch the bottom before the

pump switches off. Make sure that the float cannot get caught on anything. If the float

cannot transmit the ‘OFF’ signal, the pump will continue to work until it runs dry and

burns itself out.

Locating and moving

- Make sure the pump is positioned at a stable location, particularly if you want it to

work automatically.

- Ensure that the float can move around freely, particularly if it is to work automatically;

a possible shaft should be at least 40x40x50 cm. great!

- Ensure that the suction openings are not blocked (not even partially). If the pump is

positioned on a soft surface (e.g. a sand bed), place it on a tile or something similar.

- Do not use the electrical cable or float cable to lift the pump or hang it up. If you wish

to locate the pump in a water source or shaft, use a rope that is attached to the

handle to do so.

OPERATION

 Before use, check that the values of the socket to which you wish to connect the

pump correspond to those on the type plate on the pump itself (230V-50Hz) and that

the socket is earthed (max. 30mAmp) and has an earth leakage circuit breaker

(nominal voltage ≤30 mA). Make sure that no people present in the space to be

pumped out (cellar/boat/pond etc).

Automated function

Once you have plugged the device into the socket, the pump will switch on automatically

when the water exceeds the set minimum level and switch off when the set minimum

level has been obtained.

This means that the pump can be left on at all times and will keep the water in a cellar or

boat, for example, at the required level. Bear in mind that this pump is not designed to

be used continuously; it must be switched off at regular intervals.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eurom Flow 400 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eurom Flow 400 Manual

Product: