When the rack can no longer be rotated on the trailer tow bar, rotate the securing bolt of the quick locking mechanism until it engages. Now close the quick
locking mechanism with the supplied padlock and remove the key from the lock. Store the key carefully and in a safe place. The bicycle rack is now secured to
prevent theft.
Regularly check the rm seating of the rack on the trailer tow bar as well as the attachment of the bicycles to the rack. Also regularly check the functions of the
lighting system of your bicycle rack.
Slight signs of pressure on the two bar ball are normal and do not inuence the functionality.
5.3 MOUNTING THE BICYCLES TO THE RACK
5.4 USING THE TENSIONRELIEF STRAP
These instructions describe the use with estates and compact vehicles with a hatchback (rear door). With boots
(saloons) proceed appropriately.
Before mounting the tension-relief strap, remove dust and dirt from the upper region of the rear door in order
to prevent scratching and abrasion when travelling with the tow-bar rack.
Open the rear door of your vehicle. Guide the free end of the strap from the inside to the outside between the
rear door and the edge of the roof. Leave approximately 20 cm free between the strap anchor and the edge of
the roof. Carefully close the rear door. Make sure that the strap lies at and straight between the seals. Now
slowly pull the strap until the strap anchor meets the panel of the roof liner and the rear door.
The bicycle rack may not be used without this safety strap.
Make sure that any roof edge spoilers are not damaged and that the functionality of
the tension-relief strap is not inuenced by such spoilers.
The rst bicycle is placed in the rst wheel rail (closest to the vehicle) and secured to the U-bracket
with the short frame holder. To do this, use the side of the frame holder with the tensioning strap
to secure to the bicycle frame. The wheels are secured by placing the tensioning straps around the
wheel rim of your bicycle and tightening the straps. Caution: The front wheel must also be secured
to prevent it from turning using an additional small tensioning strap. To do this, secure the front
wheel to the rail again at a dierent position (see picture).
The second bicycle is usually placed in the second rail, facing the opposite direction to the rst and
secured to the U-bracket with the long frame holder. The wheels are secured in the same way as for
the rst bicycle. The third bicycle is placed in the third rail and secured with the long frame holder
to the U-shaped bar. The fourth bicycle is secured in the fourth rail. With the wheel-to-wheel frame
holder connect the frame of the fourth bicycle with that of the third. The bicycle wheels are secured
in the same way as those of the rst bicycle. It may be necessary to use a dierent method than
the one described to secure the bicycles individually on the rack to ensure that the frame holders
may be correctly secured. Now secure the bicycles with the long safety strap. Wrap the safety strap
through the bicycle frames and the U-shaped bar and tighten.
Now attach the lock section of the strap to the U-bar as shown on Figures 1 to 4.
Safety strap
Figure 1Figure 2Figure 3Figure 4
Tension-relief strap
4 x Tensioning strap, short
Connect both parts of the tension-relief strap as shown on Figures 5 to 7.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eufab 11556 - Amber IV at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eufab 11556 - Amber IV in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 7.9 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
