Remove the screws from the lamp mount of the license plate holder before mounting. Insert the screws through the vertical slots of the license plate holder
(see picture). Start the screws at the threaded holes of the lamp mount, but do not tighten yet. Align the license plate folder so that it is at the same height as
the rear lights. Now tighten the screws.
The mounting clips for securing the license plate are push-out parts in the holder.
Break out two of the clips. Slide the license plate into the holder, then push the
clips into the cut-outs to secure the license plate.
Lay the cables along the tube of the base frame. The cables may not be bent, stretched or crushed, e.g. in the vicinity of the folding
mechanism. Secure the cables with the supplied cable ties. When you are nished, trim any excess material from the cable ties using
cutting pliers.
5.1.7 INSERTING THE LICENSE PLATE
5.1.8 LAYING ELECTRICAL CABLES
Cut-outs
Clips
5.1.9 ATTACHING THE PLASTIC COVERS
5.1.10 MOUNTING THE SHORT TENSIONING STRAPS
Fit the plastic covers onto the middle of the wheel rails.
nsert the short tensioning strap from the inside to the outside below the bike holder and then from the outside to the
inside through the slots of the bike holder (see picture).
4 x Plastic cover
8 x Tensioning strap, short
The padlock must always be used as additional security
when using the bicycle rack.
Ensure that the trailer tow bar is undamaged, clean and free of grease.
Before you put the bicycle rack on the trailer tow bar, familiarise yourself with the
quick locking system.
The quick locking mechanism is a component with a lever. Activating the lever
opens or closes the quick locking mechanism. With the help of the securing bolt
and the padlock, the quick locking system may be locked and secured.
5.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR
Safety/locking pin
Lock nut
Lock
Lever
Adjusting screw for
qick locking system
Park your vehicle on a level surface.
Apply the handbrake.
Remove the securing bolt from the quick locking mechanism and rotate by 90° to prevent it from engaging again. Open the quick locking mechanism by lifting
the lever.
Place the rack, from above, horizontally onto the trailer tow bar. Push the lever of the quick locking mechanism down (force required is approximately 35 - -40
kg) as far as it will go (the lever will remain in the horizontal position).
Check whether the bike rack is securely and rmly positioned on the trailer tow bar and can no longer be rotated. If this is not the case, the quick locking mecha-
nism must be readjusted. Lift the lever and remove the rack from the trailer tow bar. Remove the protective cap of the adjusting screw. Undo the lock nut of the
adjusting screw and rotate the adjusting screw on the quick locking mechanism tighter by a quarter turn. Then tighten the lock nut again.
Replace the rack back on the trailer tow bar and check whether the rack is securely and rmly positioned on the tow bar. Repeat the adjustment process until
the rack is secure and rm. Push the protective cap back onto the adjustment screw.
Caution: Always make sure that the lock nut on the adjusting screw is correctly tightened!
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eufab 11556 - Amber IV at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eufab 11556 - Amber IV in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 7.9 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
