The general operating permit must be carried in the vehicle when the rack is mounted.
Do not travel with the bicycle rack empty. Store it in the boot of your vehicle. This prevents increased fuel consumption and
protects the rack.
The driver is always responsible for ensuring that the load and the load securing meet the regulations.
1 x Base frame8 x Wheel rails16 x Lock screw M6 x 50
16 x Washer 17.8 x 6.5 x 1.1
16 x Nut M6
5.1 MOUNTING THE BICYCLE RACK
The bicycle rack must rst be assembled. Take all of the components out of the packaging and set them out clearly. Every stage is described and clearly shows
which components are required for the assembly of the rack.
Two wheel rails form a pair. Place four pairs of wheel rails, with the plastic shells on the outside, parallel on the base frame so that the drilled holes in the rail
match the holes in the base frame. Secure each wheel rail to the base frame with the lock screws M6 x 50, 17.8 x 6.5 x 1.1 washers and self-tapping nuts M6.
5.1.1 MOUNTING THE WHEEL RAILS ON THE BASE FRAME
5. OPERATING INSTRUCTIONS
Join the two halves of the lamp mount set together. This is made easier by the small guide element which is already mounted on one side. Push the rails together
and secure the connection with the cross-headed screw (M5x12), spring washer, washer 9.8 x 5.4 x 0.9
Insert the cross-headed screws M5 x 35 with spring washers and washers, from below, through the vertical drilled holes of the lamp mount. Insert the
screws through the threaded holes on the underside at the end of the lamp mount. Tighten the screws.
1 x Lamp mounting set
2 x Cross-headed screw M5 x 35
2 x Spring washer 8.1 x 5.5 x 1.2
2 x Washer 9.7 x 5.3 x 0.9
Cross-headed screw M5 x 12
5.1.2 MOUNTING THE LAMP MOUNTS
5.1.3 SECURING THE LIGHT MOUNT TO THE BASE FRAME
Í
Í
Í
Now t the U-bracket onto the intended pipe sleeves. Push the lock screws M8 x 60 from the outside, through the drilled holes of the U-bracket and the pipe
sleeves. Place the washers and knob nuts M8 on the ends of the screws and tighten the knob nuts rmly.
Undo the handle screw of the frame holder and rotate out fully. Open the cu of the frame holder and place the inserts around the U-bracket at a position
suitable for your bicycle. Place the cu around the inserts and push rmly together. Close the frame holder using the handle screw (but do not tighten).
The wheel-to-wheel frame holder is only required when you secure a fourth bicycle to the rack.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eufab 11556 - Amber IV at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eufab 11556 - Amber IV in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 7.9 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
