Manual Eufab 11417 - James (page 11 of 24) (English, German, French, Italian)

807233

Zoom out

Zoom in

1/24

2 x Washer 5.4 x 5.2 x 0.9

2 x Screw M5 x 10

Join the two parts of the lamp mount together. This is made easier by the

small guide element which is already mounted on one side. Push the two

pieces together and secure the connection with the screws M5 x 10 and

washers.

Rear lights, left and right

Light protection, left and right 4 x Nut M5

4 x Washer 13.7 x 5.4 x 0.9

Insert the left rear light (with fog light) into the left light protection ( xture

eye right, cable guide bottom). Pay attention to ensure that the cable is

correctly inside the duct. Now guide the threaded bolts of the light through

the drilled holes on the left side of the lamp mount and screw the rear light

 rmly into place using the nuts M5 and washers 13.7 x 5.4 x 0.9. Do the

same for the right rear light (with reversing light).

Now mount the entire lamp mount under the second wheel rail. To do this

adjust the short link screws in the second wheel rail to the distance of the

lamp mount holders. Guide the screws through the drilled holes in the

holders of the lamp mount and screw into place using the washers

17.6 x 6.5 x 1.1 and wing nuts.

5.1.5 INSTALLATION OF THE REAR LIGHTS

2 x Washer 17.6 x 6.5 x 1.1 2 x Wing nut

Mount the license plate holder using the already mounted Allen screws and

washers to the lamp mount in such a way that the lamps and the license

plate holder are level.

The mounting clips for securing the license plate are push-out parts in the

holder. Break out two of the clips.

Slide the license plate into the holder, then push the clips into the cut-outs

to secure the license plate.

5.1.6 MOUNTING THE LICENSE PLATE HOLDER

Cut-out for installation clips

Clips

Cut-out for installation clips

5.1.7 MOUNTING THE FRAME HOLDER

Use the key to open the lock on the knob nut and remove the key. Unscrew

the knob nut completely from the frame holder by rotating anti-clockwise.

Now remove the washer, the frame clip and the tube-side spacer from the

thread. Place the thread on a  rm and scratch-proof surface and push the

cu and tube carefully in the direction of the underlay. This releases the

lock screw from the cu and also removes the cover cap. Pull the lock screw

completely from the cu and separate the tube from the cu . Open the cu

and remove the rubber inlay. Place the rubber inlay around the U-bracket in

a position suitable for your bicycle (will depend Clips Cut-out for installation

clips on frame size and shape). Now place the cu over the rubber inlay and

squeeze together  rmly, in doing so, make sure that the rubber inlay is not

crushed or creased. Insert the lock screw through the two drilled holes of

the cu . Gently rotating will tell you whether the square of the lock screw

is seated  rmly. Now place the components on the lock screw in this order:

Tube, spacer (with the curve facing the frame clip), frame clip,

spacer (with the curve facing the frame clip) and washer. Screw the knob

nut into place by turning clockwise. Replace the cover cap back on the cu .

Frame holder, short Frame holder, long

5.1.8 LAYING ELECTRICAL CABLES

Lay the cables along the tube of the rack plate. The cables may not be

bent, stretched or crushed, e.g. in the vicinity of the folding mechanism.

Secure the cables with the supplied cable ties. When you are  nished, trim

any excess material from the cable ties using cutting pliers.

Adjustable bolt

Brake lever

Safety pin

Hole for padlock

Lock for brake lever

Lever for tipping mechanism

5.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR

Ensure that the trailer tow bar is undamaged, clean and free of grease.

Remove any existing paintwork from the coupling head.

Before you put the bicycle rack on the trailer tow bar, familiarise yourself

with the quick locking system.

The quick locking mechanism is a component with a tension lever.

Activating the tension lever opens or closes the quick locking mechanism.

With the help of the securing bolt and the padlock, the quick locking system

may be locked and secured.

The padlock is always required when using the bicycle

rack.

Park your vehicle on a level surface. Apply the handbrake. Remove the

securing bolt from the quick locking mechanism and rotate by 90° to

prevent it from engaging again. Open the quick locking mechanism by

lifting the tension lever.

Place the rack, from above, horizontally onto the trailer tow bar. Push

the tension lever of the quick locking mechanism down (force required is

approximately 35 - 40 kg) as far as it will go (the lever will remain in the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 11417 - James in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eufab 11417 - James Manual

Product: